STM32F0x2 Peripheral Coverage

Overall: 2765/3614 fields covered

ADC

0x40012400: Analog-to-digital converter

59/60 fields covered. Toggle Registers.

ISR

interrupt and status register

Offset: 0x0, reset: 0x00000000, access: read-write

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								AWD rw			OVR rw	EOSEQ rw	EOC rw	EOSMP rw	ADRDY rw

Toggle Fields.

ADRDY

Bit 0: ADC ready.

Allowed values:
0: NotReady: ADC not yet ready to start conversion
1: Ready: ADC ready to start conversion

EOSMP

Bit 1: End of sampling flag.

Allowed values:
0: NotAtEnd: Not at the end of the samplings phase
1: AtEnd: End of sampling phase reached

EOC

Bit 2: End of conversion flag.

Allowed values:
0: NotComplete: Channel conversion is not complete
1: Complete: Channel conversion complete

EOSEQ

Bit 3: End of sequence flag.

Allowed values:
0: NotComplete: Conversion sequence is not complete
1: Complete: Conversion sequence complete

OVR

Bit 4: ADC overrun.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

AWD

Bit 7: Analog watchdog flag.

Allowed values:
0: NoEvent: No analog watchdog event occurred
1: Event: Analog watchdog event occurred

IER

interrupt enable register

Offset: 0x4, reset: 0x00000000, access: read-write

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								AWDIE rw			OVRIE rw	EOSEQIE rw	EOCIE rw	EOSMPIE rw	ADRDYIE rw

Toggle Fields.

ADRDYIE

Bit 0: ADC ready interrupt enable.

Allowed values:
0: Disabled: ADC ready interrupt disabled
1: Enabled: ADC ready interrupt enabled

EOSMPIE

Bit 1: End of sampling flag interrupt enable.

Allowed values:
0: Disabled: End of sampling interrupt disabled
1: Enabled: End of sampling interrupt enabled

EOCIE

Bit 2: End of conversion interrupt enable.

Allowed values:
0: Disabled: End of conversion interrupt disabled
1: Enabled: End of conversion interrupt enabled

EOSEQIE

Bit 3: End of conversion sequence interrupt enable.

Allowed values:
0: Disabled: End of conversion sequence interrupt disabled
1: Enabled: End of conversion sequence interrupt enabled

OVRIE

Bit 4: Overrun interrupt enable.

Allowed values:
0: Disabled: Overrun interrupt disabled
1: Enabled: Overrun interrupt enabled

AWDIE

Bit 7: Analog watchdog interrupt enable.

Allowed values:
0: Disabled: Analog watchdog interrupt disabled
1: Enabled: Analog watchdog interrupt enabled

CR

control register

Offset: 0x8, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADCAL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											ADSTP rw		ADSTART rw	ADDIS rw	ADEN rw

Toggle Fields.

ADEN

Bit 0: ADC enable command.

Allowed values:
0: Disabled: ADC disabled
1: Enabled: ADC enabled

ADDIS

Bit 1: ADC disable command.

Allowed values:
0: NotDisabling: No disable command active
1: Disabling: ADC disabling

ADSTART

Bit 2: ADC start conversion command.

Allowed values:
0: NotActive: No conversion ongoing
1: Active: ADC operating and may be converting

ADSTP

Bit 4: ADC stop conversion command.

Allowed values:
0: NotStopping: No stop command active
1: Stopping: ADC stopping conversion

ADCAL

Bit 31: ADC calibration.

Allowed values:
0: NotCalibrating: ADC calibration either not yet performed or completed
1: Calibrating: ADC calibration in progress

CFGR1

configuration register 1

Offset: 0xC, reset: 0x00000000, access: read-write

15/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	AWDCH rw							AWDEN rw	AWDSGL rw						DISCEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AUTOFF rw	WAIT rw	CONT rw	OVRMOD rw	EXTEN rw			EXTSEL rw			ALIGN rw	RES rw		SCANDIR rw	DMACFG rw	DMAEN rw

Toggle Fields.

DMAEN

Bit 0: Direct memory access enable.

Allowed values:
0: Disabled: DMA mode disabled
1: Enabled: DMA mode enabled

DMACFG

Bit 1: Direct memery access configuration.

Allowed values:
0: OneShot: DMA one shot mode
1: Circular: DMA circular mode

SCANDIR

Bit 2: Scan sequence direction.

Allowed values:
0: Upward: Upward scan (from CHSEL0 to CHSEL18)
1: Backward: Backward scan (from CHSEL18 to CHSEL0)

RES

Bits 3-4: Data resolution.

Allowed values:
0: TwelveBit: 12-bit (14 ADCCLK cycles)
1: TenBit: 10-bit (13 ADCCLK cycles)
2: EightBit: 8-bit (11 ADCCLK cycles)
3: SixBit: 6-bit (9 ADCCLK cycles)

ALIGN

Bit 5: Data alignment.

Allowed values:
0: Right: Right alignment
1: Left: Left alignment

EXTSEL

Bits 6-8: External trigger selection.

Allowed values:
2: TIM2_TRGO: Timer 2 TRGO event
0: TIM1_TRGO: Timer 1 TRGO Event
1: TIM1_CC4: Timer 1 CC4 event
3: TIM3_TRGO: Timer 3 TRGO event
4: TIM15_TRGO: Timer 15 TRGO event

EXTEN

Bits 10-11: External trigger enable and polarity selection.

Allowed values:
0: Disabled: Trigger detection disabled
1: RisingEdge: Trigger detection on the rising edge
2: FallingEdge: Trigger detection on the falling edge
3: BothEdges: Trigger detection on both the rising and falling edges

OVRMOD

Bit 12: Overrun management mode.

Allowed values:
0: Preserved: ADC_DR register is preserved with the old data when an overrun is detected
1: Overwritten: ADC_DR register is overwritten with the last conversion result when an overrun is detected

CONT

Bit 13: Single / continuous conversion mode.

Allowed values:
0: Single: Single conversion mode
1: Continuous: Continuous conversion mode

WAIT

Bit 14: Wait conversion mode.

Allowed values:
0: Disabled: Wait conversion mode off
1: Enabled: Wait conversion mode on

AUTOFF

Bit 15: Auto-off mode.

Allowed values:
0: Disabled: Auto-off mode disabled
1: Enabled: Auto-off mode enabled

DISCEN

Bit 16: Discontinuous mode.

Allowed values:
0: Disabled: Discontinuous mode on regular channels disabled
1: Enabled: Discontinuous mode on regular channels enabled

AWDSGL

Bit 22: Enable the watchdog on a single channel or on all channels.

Allowed values:
0: AllChannels: Analog watchdog enabled on all channels
1: SingleChannel: Analog watchdog enabled on a single channel

AWDEN

Bit 23: Analog watchdog enable.

Allowed values:
0: Disabled: Analog watchdog disabled on regular channels
1: Enabled: Analog watchdog enabled on regular channels

AWDCH

Bits 26-30: Analog watchdog channel selection.

Allowed values: 0-18

CFGR2

configuration register 2

Offset: 0x10, reset: 0x00008000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CKMODE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0

Toggle Fields.

CKMODE

Bits 30-31: ADC clock mode.

Allowed values:
0: ADCCLK: Asynchronous clock mode
1: PCLK_Div2: Synchronous clock mode (PCLK/2)
2: PCLK_Div4: Sychronous clock mode (PCLK/4)

SMPR

sampling time register

Offset: 0x14, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													SMP rw

Toggle Fields.

SMP

Bits 0-2: Sampling time selection.

Allowed values:
0: Cycles1_5: 1.5 cycles
1: Cycles7_5: 7.5 cycles
2: Cycles13_5: 13.5 cycles
3: Cycles28_5: 28.5 cycles
4: Cycles41_5: 41.5 cycles
5: Cycles55_5: 55.5 cycles
6: Cycles71_5: 71.5 cycles
7: Cycles239_5: 239.5 cycles

TR

watchdog threshold register

Offset: 0x20, reset: 0x00000FFF, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				HT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				LT rw

Toggle Fields.

LT

Bits 0-11: Analog watchdog lower threshold.

Allowed values: 0-4095

HT

Bits 16-27: Analog watchdog higher threshold.

Allowed values: 0-4095

CHSELR

channel selection register

Offset: 0x28, reset: 0x00000000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													CHSEL18 rw	CHSEL17 rw	CHSEL16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CHSEL15 rw	CHSEL14 rw	CHSEL13 rw	CHSEL12 rw	CHSEL11 rw	CHSEL10 rw	CHSEL9 rw	CHSEL8 rw	CHSEL7 rw	CHSEL6 rw	CHSEL5 rw	CHSEL4 rw	CHSEL3 rw	CHSEL2 rw	CHSEL1 rw	CHSEL0 rw

Toggle Fields.

CHSEL0

Bit 0: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL1

Bit 1: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL2

Bit 2: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL3

Bit 3: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL4

Bit 4: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL5

Bit 5: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL6

Bit 6: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL7

Bit 7: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL8

Bit 8: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL9

Bit 9: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL10

Bit 10: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL11

Bit 11: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL12

Bit 12: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL13

Bit 13: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL14

Bit 14: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL15

Bit 15: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL16

Bit 16: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL17

Bit 17: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

CHSEL18

Bit 18: Channel-x selection.

Allowed values:
0: NotSelected: Input Channel is not selected for conversion
1: Selected: Input Channel is selected for conversion

DR

data register

Offset: 0x40, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA r

Toggle Fields.

DATA

Bits 0-15: Converted data.

CCR

common configuration register

Offset: 0x308, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							VBATEN rw	TSEN rw	VREFEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0

Toggle Fields.

VREFEN

Bit 22: Temperature sensor and VREFINT enable.

Allowed values:
0: Disabled: V_REFINT channel disabled
1: Enabled: V_REFINT channel enabled

TSEN

Bit 23: Temperature sensor enable.

Allowed values:
0: Disabled: Temperature sensor disabled
1: Enabled: Temperature sensor enabled

VBATEN

Bit 24: VBAT enable.

Allowed values:
0: Disabled: V_BAT channel disabled
1: Enabled: V_BAT channel enabled

CAN

0x40006400: Controller area network

57/280 fields covered. Toggle Registers.

FR1

Filter bank 0 register 1

Offset: 0x0, reset: 0x00000000, access: read-write

0/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB31 rw	FB30 rw	FB29 rw	FB28 rw	FB27 rw	FB26 rw	FB25 rw	FB24 rw	FB23 rw	FB22 rw	FB21 rw	FB20 rw	FB19 rw	FB18 rw	FB17 rw	FB16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB15 rw	FB14 rw	FB13 rw	FB12 rw	FB11 rw	FB10 rw	FB9 rw	FB8 rw	FB7 rw	FB6 rw	FB5 rw	FB4 rw	FB3 rw	FB2 rw	FB1 rw	FB0 rw

Toggle Fields.

FB0

Bit 0: Filter bits.

FB1

Bit 1: Filter bits.

FB2

Bit 2: Filter bits.

FB3

Bit 3: Filter bits.

FB4

Bit 4: Filter bits.

FB5

Bit 5: Filter bits.

FB6

Bit 6: Filter bits.

FB7

Bit 7: Filter bits.

FB8

Bit 8: Filter bits.

FB9

Bit 9: Filter bits.

FB10

Bit 10: Filter bits.

FB11

Bit 11: Filter bits.

FB12

Bit 12: Filter bits.

FB13

Bit 13: Filter bits.

FB14

Bit 14: Filter bits.

FB15

Bit 15: Filter bits.

FB16

Bit 16: Filter bits.

FB17

Bit 17: Filter bits.

FB18

Bit 18: Filter bits.

FB19

Bit 19: Filter bits.

FB20

Bit 20: Filter bits.

FB21

Bit 21: Filter bits.

FB22

Bit 22: Filter bits.

FB23

Bit 23: Filter bits.

FB24

Bit 24: Filter bits.

FB25

Bit 25: Filter bits.

FB26

Bit 26: Filter bits.

FB27

Bit 27: Filter bits.

FB28

Bit 28: Filter bits.

FB29

Bit 29: Filter bits.

FB30

Bit 30: Filter bits.

FB31

Bit 31: Filter bits.

FR2

Filter bank 0 register 2

Offset: 0x4, reset: 0x00000000, access: read-write

0/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FB31 rw	FB30 rw	FB29 rw	FB28 rw	FB27 rw	FB26 rw	FB25 rw	FB24 rw	FB23 rw	FB22 rw	FB21 rw	FB20 rw	FB19 rw	FB18 rw	FB17 rw	FB16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FB15 rw	FB14 rw	FB13 rw	FB12 rw	FB11 rw	FB10 rw	FB9 rw	FB8 rw	FB7 rw	FB6 rw	FB5 rw	FB4 rw	FB3 rw	FB2 rw	FB1 rw	FB0 rw

Toggle Fields.

FB0

Bit 0: Filter bits.

FB1

Bit 1: Filter bits.

FB2

Bit 2: Filter bits.

FB3

Bit 3: Filter bits.

FB4

Bit 4: Filter bits.

FB5

Bit 5: Filter bits.

FB6

Bit 6: Filter bits.

FB7

Bit 7: Filter bits.

FB8

Bit 8: Filter bits.

FB9

Bit 9: Filter bits.

FB10

Bit 10: Filter bits.

FB11

Bit 11: Filter bits.

FB12

Bit 12: Filter bits.

FB13

Bit 13: Filter bits.

FB14

Bit 14: Filter bits.

FB15

Bit 15: Filter bits.

FB16

Bit 16: Filter bits.

FB17

Bit 17: Filter bits.

FB18

Bit 18: Filter bits.

FB19

Bit 19: Filter bits.

FB20

Bit 20: Filter bits.

FB21

Bit 21: Filter bits.

FB22

Bit 22: Filter bits.

FB23

Bit 23: Filter bits.

FB24

Bit 24: Filter bits.

FB25

Bit 25: Filter bits.

FB26

Bit 26: Filter bits.

FB27

Bit 27: Filter bits.

FB28

Bit 28: Filter bits.

FB29

Bit 29: Filter bits.

FB30

Bit 30: Filter bits.

FB31

Bit 31: Filter bits.

RDLR

CAN_RDL0R

Offset: 0x8, reset: 0x00000000, access: read-only

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA3 r								DATA2 r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA1 r								DATA0 r

Toggle Fields.

DATA0

Bits 0-7: DATA0.

DATA1

Bits 8-15: DATA1.

DATA2

Bits 16-23: DATA2.

DATA3

Bits 24-31: DATA3.

RDHR

CAN_RDH0R

Offset: 0xC, reset: 0x00000000, access: read-only

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DATA7 r								DATA6 r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DATA5 r								DATA4 r

Toggle Fields.

DATA4

Bits 0-7: DATA4.

DATA5

Bits 8-15: DATA5.

DATA6

Bits 16-23: DATA6.

DATA7

Bits 24-31: DATA7.

IER

CAN_IER

Offset: 0x14, reset: 0x00000000, access: read-write

14/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
														SLKIE rw	WKUIE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ERRIE rw				LECIE rw	BOFIE rw	EPVIE rw	EWGIE rw		FOVIE1 rw	FFIE1 rw	FMPIE1 rw	FOVIE0 rw	FFIE0 rw	FMPIE0 rw	TMEIE rw

Toggle Fields.

TMEIE

Bit 0: TMEIE.

Allowed values:
0: Disabled: No interrupt when RQCPx bit is set
1: Enabled: Interrupt generated when RQCPx bit is set

FMPIE0

Bit 1: FMPIE0.

Allowed values:
0: Disabled: No interrupt generated when state of FMP[1:0] bits are not 00
1: Enabled: Interrupt generated when state of FMP[1:0] bits are not 00b

FFIE0

Bit 2: FFIE0.

Allowed values:
0: Disabled: No interrupt when FULL bit is set
1: Enabled: Interrupt generated when FULL bit is set

FOVIE0

Bit 3: FOVIE0.

Allowed values:
0: Disabled: No interrupt when FOVR bit is set
1: Enabled: Interrupt generated when FOVR bit is set

FMPIE1

Bit 4: FMPIE1.

Allowed values:
0: Disabled: No interrupt generated when state of FMP[1:0] bits are not 00b
1: Enabled: Interrupt generated when state of FMP[1:0] bits are not 00b

FFIE1

Bit 5: FFIE1.

Allowed values:
0: Disabled: No interrupt when FULL bit is set
1: Enabled: Interrupt generated when FULL bit is set

FOVIE1

Bit 6: FOVIE1.

Allowed values:
0: Disabled: No interrupt when FOVR is set
1: Enabled: Interrupt generation when FOVR is set

EWGIE

Bit 8: EWGIE.

Allowed values:
0: Disabled: ERRI bit will not be set when EWGF is set
1: Enabled: ERRI bit will be set when EWGF is set

EPVIE

Bit 9: EPVIE.

Allowed values:
0: Disabled: ERRI bit will not be set when EPVF is set
1: Enabled: ERRI bit will be set when EPVF is set

BOFIE

Bit 10: BOFIE.

Allowed values:
0: Disabled: ERRI bit will not be set when BOFF is set
1: Enabled: ERRI bit will be set when BOFF is set

LECIE

Bit 11: LECIE.

Allowed values:
0: Disabled: ERRI bit will not be set when the error code in LEC[2:0] is set by hardware on error detection
1: Enabled: ERRI bit will be set when the error code in LEC[2:0] is set by hardware on error detection

ERRIE

Bit 15: ERRIE.

Allowed values:
0: Disabled: No interrupt will be generated when an error condition is pending in the CAN_ESR
1: Enabled: An interrupt will be generation when an error condition is pending in the CAN_ESR

WKUIE

Bit 16: WKUIE.

Allowed values:
0: Disabled: No interrupt when WKUI is set
1: Enabled: Interrupt generated when WKUI bit is set

SLKIE

Bit 17: SLKIE.

Allowed values:
0: Disabled: No interrupt when SLAKI bit is set
1: Enabled: Interrupt generated when SLAKI bit is set

ESR

CAN_ESR

Offset: 0x18, reset: 0x00000000, access: Unspecified

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
REC r								TEC r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									LEC rw				BOFF r	EPVF r	EWGF r

Toggle Fields.

EWGF

Bit 0: EWGF.

EPVF

Bit 1: EPVF.

BOFF

Bit 2: BOFF.

LEC

Bits 4-6: LEC.

Allowed values:
0: NoError: No Error
1: Stuff: Stuff Error
2: Form: Form Error
3: Ack: Acknowledgment Error
4: BitRecessive: Bit recessive Error
5: BitDominant: Bit dominant Error
6: Crc: CRC Error
7: Custom: Set by software

TEC

Bits 16-23: TEC.

REC

Bits 24-31: REC.

BTR

CAN BTR

Offset: 0x1C, reset: 0x00000000, access: read-write

2/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SILM rw	LBKM rw					SJW rw			TS2 rw			TS1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						BRP rw

Toggle Fields.

BRP

Bits 0-9: BRP.

TS1

Bits 16-19: TS1.

TS2

Bits 20-22: TS2.

SJW

Bits 24-25: SJW.

LBKM

Bit 30: LBKM.

Allowed values:
0: Disabled: Loop Back Mode disabled
1: Enabled: Loop Back Mode enabled

SILM

Bit 31: SILM.

Allowed values:
0: Normal: Normal operation
1: Silent: Silent Mode

FMR

CAN_FMR

Offset: 0x200, reset: 0x00000000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CAN2SB rw													FINIT rw

Toggle Fields.

FINIT

Bit 0: FINIT.

CAN2SB

Bits 8-13: CAN2SB.

FM1R

CAN_FM1R

Offset: 0x204, reset: 0x00000000, access: read-write

0/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				FBM27 rw	FBM26 rw	FBM25 rw	FBM24 rw	FBM23 rw	FBM22 rw	FBM21 rw	FBM20 rw	FBM19 rw	FBM18 rw	FBM17 rw	FBM16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FBM15 rw	FBM14 rw	FBM13 rw	FBM12 rw	FBM11 rw	FBM10 rw	FBM9 rw	FBM8 rw	FBM7 rw	FBM6 rw	FBM5 rw	FBM4 rw	FBM3 rw	FBM2 rw	FBM1 rw	FBM0 rw

Toggle Fields.

FBM0

Bit 0: Filter mode.

FBM1

Bit 1: Filter mode.

FBM2

Bit 2: Filter mode.

FBM3

Bit 3: Filter mode.

FBM4

Bit 4: Filter mode.

FBM5

Bit 5: Filter mode.

FBM6

Bit 6: Filter mode.

FBM7

Bit 7: Filter mode.

FBM8

Bit 8: Filter mode.

FBM9

Bit 9: Filter mode.

FBM10

Bit 10: Filter mode.

FBM11

Bit 11: Filter mode.

FBM12

Bit 12: Filter mode.

FBM13

Bit 13: Filter mode.

FBM14

Bit 14: Filter mode.

FBM15

Bit 15: Filter mode.

FBM16

Bit 16: Filter mode.

FBM17

Bit 17: Filter mode.

FBM18

Bit 18: Filter mode.

FBM19

Bit 19: Filter mode.

FBM20

Bit 20: Filter mode.

FBM21

Bit 21: Filter mode.

FBM22

Bit 22: Filter mode.

FBM23

Bit 23: Filter mode.

FBM24

Bit 24: Filter mode.

FBM25

Bit 25: Filter mode.

FBM26

Bit 26: Filter mode.

FBM27

Bit 27: Filter mode.

FS1R

CAN_FS1R

Offset: 0x20C, reset: 0x00000000, access: read-write

0/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				FSC27 rw	FSC26 rw	FSC25 rw	FSC24 rw	FSC23 rw	FSC22 rw	FSC21 rw	FSC20 rw	FSC19 rw	FSC18 rw	FSC17 rw	FSC16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FSC15 rw	FSC14 rw	FSC13 rw	FSC12 rw	FSC11 rw	FSC10 rw	FSC9 rw	FSC8 rw	FSC7 rw	FSC6 rw	FSC5 rw	FSC4 rw	FSC3 rw	FSC2 rw	FSC1 rw	FSC0 rw

Toggle Fields.

FSC0

Bit 0: Filter scale configuration.

FSC1

Bit 1: Filter scale configuration.

FSC2

Bit 2: Filter scale configuration.

FSC3

Bit 3: Filter scale configuration.

FSC4

Bit 4: Filter scale configuration.

FSC5

Bit 5: Filter scale configuration.

FSC6

Bit 6: Filter scale configuration.

FSC7

Bit 7: Filter scale configuration.

FSC8

Bit 8: Filter scale configuration.

FSC9

Bit 9: Filter scale configuration.

FSC10

Bit 10: Filter scale configuration.

FSC11

Bit 11: Filter scale configuration.

FSC12

Bit 12: Filter scale configuration.

FSC13

Bit 13: Filter scale configuration.

FSC14

Bit 14: Filter scale configuration.

FSC15

Bit 15: Filter scale configuration.

FSC16

Bit 16: Filter scale configuration.

FSC17

Bit 17: Filter scale configuration.

FSC18

Bit 18: Filter scale configuration.

FSC19

Bit 19: Filter scale configuration.

FSC20

Bit 20: Filter scale configuration.

FSC21

Bit 21: Filter scale configuration.

FSC22

Bit 22: Filter scale configuration.

FSC23

Bit 23: Filter scale configuration.

FSC24

Bit 24: Filter scale configuration.

FSC25

Bit 25: Filter scale configuration.

FSC26

Bit 26: Filter scale configuration.

FSC27

Bit 27: Filter scale configuration.

FFA1R

CAN_FFA1R

Offset: 0x214, reset: 0x00000000, access: read-write

0/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				FFA27 rw	FFA26 rw	FFA25 rw	FFA24 rw	FFA23 rw	FFA22 rw	FFA21 rw	FFA20 rw	FFA19 rw	FFA18 rw	FFA17 rw	FFA16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FFA15 rw	FFA14 rw	FFA13 rw	FFA12 rw	FFA11 rw	FFA10 rw	FFA9 rw	FFA8 rw	FFA7 rw	FFA6 rw	FFA5 rw	FFA4 rw	FFA3 rw	FFA2 rw	FFA1 rw	FFA0 rw

Toggle Fields.

FFA0

Bit 0: Filter FIFO assignment for filter 0.

FFA1

Bit 1: Filter FIFO assignment for filter 1.

FFA2

Bit 2: Filter FIFO assignment for filter 2.

FFA3

Bit 3: Filter FIFO assignment for filter 3.

FFA4

Bit 4: Filter FIFO assignment for filter 4.

FFA5

Bit 5: Filter FIFO assignment for filter 5.

FFA6

Bit 6: Filter FIFO assignment for filter 6.

FFA7

Bit 7: Filter FIFO assignment for filter 7.

FFA8

Bit 8: Filter FIFO assignment for filter 8.

FFA9

Bit 9: Filter FIFO assignment for filter 9.

FFA10

Bit 10: Filter FIFO assignment for filter 10.

FFA11

Bit 11: Filter FIFO assignment for filter 11.

FFA12

Bit 12: Filter FIFO assignment for filter 12.

FFA13

Bit 13: Filter FIFO assignment for filter 13.

FFA14

Bit 14: Filter FIFO assignment for filter 14.

FFA15

Bit 15: Filter FIFO assignment for filter 15.

FFA16

Bit 16: Filter FIFO assignment for filter 16.

FFA17

Bit 17: Filter FIFO assignment for filter 17.

FFA18

Bit 18: Filter FIFO assignment for filter 18.

FFA19

Bit 19: Filter FIFO assignment for filter 19.

FFA20

Bit 20: Filter FIFO assignment for filter 20.

FFA21

Bit 21: Filter FIFO assignment for filter 21.

FFA22

Bit 22: Filter FIFO assignment for filter 22.

FFA23

Bit 23: Filter FIFO assignment for filter 23.

FFA24

Bit 24: Filter FIFO assignment for filter 24.

FFA25

Bit 25: Filter FIFO assignment for filter 25.

FFA26

Bit 26: Filter FIFO assignment for filter 26.

FFA27

Bit 27: Filter FIFO assignment for filter 27.

FA1R

CAN_FA1R

Offset: 0x21C, reset: 0x00000000, access: read-write

0/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				FACT27 rw	FACT26 rw	FACT25 rw	FACT24 rw	FACT23 rw	FACT22 rw	FACT21 rw	FACT20 rw	FACT19 rw	FACT18 rw	FACT17 rw	FACT16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FACT15 rw	FACT14 rw	FACT13 rw	FACT12 rw	FACT11 rw	FACT10 rw	FACT9 rw	FACT8 rw	FACT7 rw	FACT6 rw	FACT5 rw	FACT4 rw	FACT3 rw	FACT2 rw	FACT1 rw	FACT0 rw

Toggle Fields.

FACT0

Bit 0: Filter active.

FACT1

Bit 1: Filter active.

FACT2

Bit 2: Filter active.

FACT3

Bit 3: Filter active.

FACT4

Bit 4: Filter active.

FACT5

Bit 5: Filter active.

FACT6

Bit 6: Filter active.

FACT7

Bit 7: Filter active.

FACT8

Bit 8: Filter active.

FACT9

Bit 9: Filter active.

FACT10

Bit 10: Filter active.

FACT11

Bit 11: Filter active.

FACT12

Bit 12: Filter active.

FACT13

Bit 13: Filter active.

FACT14

Bit 14: Filter active.

FACT15

Bit 15: Filter active.

FACT16

Bit 16: Filter active.

FACT17

Bit 17: Filter active.

FACT18

Bit 18: Filter active.

FACT19

Bit 19: Filter active.

FACT20

Bit 20: Filter active.

FACT21

Bit 21: Filter active.

FACT22

Bit 22: Filter active.

FACT23

Bit 23: Filter active.

FACT24

Bit 24: Filter active.

FACT25

Bit 25: Filter active.

FACT26

Bit 26: Filter active.

FACT27

Bit 27: Filter active.

CEC

0x40007800: HDMI-CEC controller

1/38 fields covered. Toggle Registers.

CR

control register

Offset: 0x0, reset: 0x00000000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													TXEOM rw	TXSOM rw	CECEN rw

Toggle Fields.

CECEN

Bit 0: CEC Enable.

TXSOM

Bit 1: Tx start of message.

TXEOM

Bit 2: Tx End Of Message.

CFGR

configuration register

Offset: 0x4, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				LBPEGEN rw	BREGEN rw	BRESTP rw	RXTOL rw	SFT rw			LSTN rw	OAR rw

Toggle Fields.

OAR

Bits 0-3: Own Address.

LSTN

Bit 4: Listen mode.

SFT

Bits 5-7: Signal Free Time.

RXTOL

Bit 8: Rx-Tolerance.

BRESTP

Bit 9: Rx-stop on bit rising error.

BREGEN

Bit 10: Generate error-bit on bit rising error.

LBPEGEN

Bit 11: Generate Error-Bit on Long Bit Period Error.

TXDR

Tx data register

Offset: 0x8, reset: 0x00000000, access: write-only

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TXD w

Toggle Fields.

TXD

Bits 0-7: Tx Data register.

RXDR

Rx Data Register

Offset: 0xC, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								RXDR r

Toggle Fields.

RXDR

Bits 0-7: CEC Rx Data Register.

ISR

Interrupt and Status Register

Offset: 0x10, reset: 0x00000000, access: read-write

0/13 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			TXACKE rw	TXERR rw	TXUDR rw	TXEND rw	TXBR rw	ARBLST rw	RXACKE rw	LBPE rw	SBPE rw	BRE rw	RXOVR rw	RXEND rw	RXBR rw

Toggle Fields.

RXBR

Bit 0: Rx-Byte Received.

RXEND

Bit 1: End Of Reception.

RXOVR

Bit 2: Rx-Overrun.

BRE

Bit 3: Rx-Bit rising error.

SBPE

Bit 4: Rx-Short Bit period error.

LBPE

Bit 5: Rx-Long Bit Period Error.

RXACKE

Bit 6: Rx-Missing Acknowledge.

ARBLST

Bit 7: Arbitration Lost.

TXBR

Bit 8: Tx-Byte Request.

TXEND

Bit 9: End of Transmission.

TXUDR

Bit 10: Tx-Buffer Underrun.

TXERR

Bit 11: Tx-Error.

TXACKE

Bit 12: Tx-Missing acknowledge error.

IER

interrupt enable register

Offset: 0x14, reset: 0x00000000, access: read-write

0/13 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			TXACKIE rw	TXERRIE rw	TXUDRIE rw	TXENDIE rw	TXBRIE rw	ARBLSTIE rw	RXACKIE rw	LBPEIE rw	SBPEIE rw	BREIE rw	RXOVRIE rw	RXENDIE rw	RXBRIE rw

Toggle Fields.

RXBRIE

Bit 0: Rx-Byte Received Interrupt Enable.

RXENDIE

Bit 1: End Of Reception Interrupt Enable.

RXOVRIE

Bit 2: Rx-Buffer Overrun Interrupt Enable.

BREIE

Bit 3: Bit Rising Error Interrupt Enable.

SBPEIE

Bit 4: Short Bit Period Error Interrupt Enable.

LBPEIE

Bit 5: Long Bit Period Error Interrupt Enable.

RXACKIE

Bit 6: Rx-Missing Acknowledge Error Interrupt Enable.

ARBLSTIE

Bit 7: Arbitration Lost Interrupt Enable.

TXBRIE

Bit 8: Tx-Byte Request Interrupt Enable.

TXENDIE

Bit 9: Tx-End of message interrupt enable.

TXUDRIE

Bit 10: Tx-Underrun interrupt enable.

TXERRIE

Bit 11: Tx-Error Interrupt Enable.

TXACKIE

Bit 12: Tx-Missing Acknowledge Error Interrupt Enable.

COMP

1073807360: General purpose comparators

18/18 fields covered. Toggle Registers.

CSR

control and status register

Offset: 0x28, reset: 0, access: Unspecified

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
COMP2LOCK rw	COMP2OUT r	COMP2HYST rw		COMP2POL rw	COMP2OUTSEL rw			WNDWEN rw	COMP2INSEL rw			COMP2MODE rw			COMP2EN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
COMP1LOCK rw	COMP1OUT r	COMP1HYST rw		COMP1POL rw	COMP1OUTSEL rw				COMP1INSEL rw			COMP1MODE rw		COMP1SW1 rw	COMP1EN rw

Toggle Fields.

COMP1EN

Bit 0: Comparator 1 enable.

Allowed values:
0: Disabled: Comparator 1 disabled
1: Enabled: Comparator 1 enabled

COMP1SW1

Bit 1: Comparator 1 non inverting input DAC switch.

Allowed values:
0: Open: Switch open
1: Closed: Switch closed

COMP1MODE

Bits 2-3: Comparator 1 mode.

Allowed values:
0: HighSpeed: High speed / full power
1: MediumSpeed: Medium speed / medium power
2: LowSpeed: Low speed / low power
3: VeryLowSpeed: Very-low speed / ultra-low power

COMP1INSEL

Bits 4-6: Comparator 1 inverting input selection.

Allowed values:
0: OneQuarterVRef: 1/4 of VRefint
1: OneHalfVRef: 1/2 of VRefint
2: ThreeQuarterVRef: 3/4 of VRefint
3: VRef: VRefint
4: Comp1_INM4: COMP1_INM4 (PA4 with DAC_OUT1 if enabled)
5: Comp1_INM5: COMP1_INM5 (PA5 with DAC_OUT2 if present and enabled)
6: Comp1_INM6: COMP1_INM6 (PA0)

COMP1OUTSEL

Bits 8-10: Comparator 1 output selection.

Allowed values:
0: NoSelection: No selection
1: Timer1BreakInput: Timer 1 break input
2: Timer1InputCapture1: Timer 1 Input capture 1
3: Timer1OCRefClearInput: Timer 1 OCrefclear input
4: Timer2InputCapture4: Timer 2 input capture 4
5: Timer2OCRefClearInput: Timer 2 OCrefclear input
6: Timer3InputCapture1: Timer 3 input capture 1
7: Timer3OCRefClearInput: Timer 3 OCrefclear input

COMP1POL

Bit 11: Comparator 1 output polarity.

Allowed values:
0: NotInverted: Output is not inverted
1: Inverted: Output is inverted

COMP1HYST

Bits 12-13: Comparator 1 hysteresis.

Allowed values:
0: NoHysteresis: No hysteresis
1: LowHysteresis: Low hysteresis
2: MediumHysteresis: Medium hysteresis
3: HighHysteresis: High hysteresis

COMP1OUT

Bit 14: Comparator 1 output.

Allowed values:
0: Low: Non-inverting input below inverting input
1: High: Non-inverting input above inverting input

COMP1LOCK

Bit 15: Comparator 1 lock.

Allowed values:
0: Unlocked: Comparator 1 CSR bits (CSR[15:0]) are read-write
1: Locked: Comparator 1 CSR bits (CSR[15:0]) are read-only

COMP2EN

Bit 16: Comparator 2 enable.

Allowed values:
0: Disabled: Comparator 2 disabled
1: Enabled: Comparator 2 enabled

COMP2MODE

Bits 18-19: Comparator 2 mode.

Allowed values:
0: HighSpeed: High speed / full power
1: MediumSpeed: Medium speed / medium power
2: LowSpeed: Low speed / low power
3: VeryLowSpeed: Very-low speed / ultra-low power

COMP2INSEL

Bits 20-22: Comparator 2 inverting input selection.

Allowed values:
0: OneQuarterVRef: 1/4 of VRefint
1: OneHalfVRef: 1/2 of VRefint
2: ThreeQuarterVRef: 3/4 of VRefint
3: VRef: VRefint
4: Comp2_INM4: COMP1_INM4 (PA4 with DAC_OUT1 if enabled)
5: Comp2_INM5: COMP1_INM5 (PA5 with DAC_OUT2 if present and enabled)
6: Comp2_INM6: COMP1_INM6 (PA2)

WNDWEN

Bit 23: Window mode enable.

Allowed values:
0: Disabled: Window mode disabled
1: Enabled: Window mode enabled

COMP2OUTSEL

Bits 24-26: Comparator 2 output selection.

COMP2POL

Bit 27: Comparator 2 output polarity.

Allowed values:
0: NotInverted: Output is not inverted
1: Inverted: Output is inverted

COMP2HYST

Bits 28-29: Comparator 2 hysteresis.

Allowed values:
0: NoHysteresis: No hysteresis
1: LowHysteresis: Low hysteresis
2: MediumHysteresis: Medium hysteresis
3: HighHysteresis: High hysteresis

COMP2OUT

Bit 30: Comparator 2 output.

Allowed values:
0: Low: Non-inverting input below inverting input
1: High: Non-inverting input above inverting input

COMP2LOCK

Bit 31: Comparator 2 lock.

Allowed values:
0: Unlocked: Comparator 2 CSR bits (CSR[31:16]) are read-write
1: Locked: Comparator 2 CSR bits (CSR[31:16]) are read-only

CRC

0x40023000: cyclic redundancy check calculation unit

7/7 fields covered. Toggle Registers.

DR

Data register

Offset: 0x0, reset: 0xFFFFFFFF, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle Fields.

DR

Bits 0-31: Data register bits.

Allowed values: 0-4294967295

IDR

Independent data register

Offset: 0x4, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								IDR rw

Toggle Fields.

IDR

Bits 0-7: General-purpose 8-bit data register bits.

Allowed values: 0-255

CR

Control register

Offset: 0x8, reset: 0x00000000, access: read-write

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REV_OUT rw	REV_IN rw		POLYSIZE rw				RESET rw

Toggle Fields.

RESET

Bit 0: reset bit.

Allowed values:
1: Reset: Resets the CRC calculation unit and sets the data register to 0xFFFF FFFF

POLYSIZE

Bits 3-4: Polynomial size.

Allowed values:
0: Polysize32: 32-bit polynomial
1: Polysize16: 16-bit polynomial
2: Polysize8: 8-bit polynomial
3: Polysize7: 7-bit polynomial

REV_IN

Bits 5-6: Reverse input data.

Allowed values:
0: Normal: Bit order not affected
1: Byte: Bit reversal done by byte
2: HalfWord: Bit reversal done by half-word
3: Word: Bit reversal done by word

REV_OUT

Bit 7: Reverse output data.

Allowed values:
0: Normal: Bit order not affected
1: Reversed: Bit reversed output

INIT

Initial CRC value

Offset: 0x10, reset: 0xFFFFFFFF, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
INIT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
INIT rw

Toggle Fields.

INIT

Bits 0-31: Programmable initial CRC value.

Allowed values: 0-4294967295

CRS

0x40006C00: Clock recovery system

9/26 fields covered. Toggle Registers.

CR

control register

Offset: 0x0, reset: 0x00002000, access: read-write

0/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		TRIM rw						SWSYNC rw	AUTOTRIMEN rw	CEN rw		ESYNCIE rw	ERRIE rw	SYNCWARNIE rw	SYNCOKIE rw

Toggle Fields.

SYNCOKIE

Bit 0: SYNC event OK interrupt enable.

SYNCWARNIE

Bit 1: SYNC warning interrupt enable.

ERRIE

Bit 2: Synchronization or trimming error interrupt enable.

ESYNCIE

Bit 3: Expected SYNC interrupt enable.

CEN

Bit 5: Frequency error counter enable.

AUTOTRIMEN

Bit 6: Automatic trimming enable.

SWSYNC

Bit 7: Generate software SYNC event.

TRIM

Bits 8-13: HSI48 oscillator smooth trimming.

CFGR

configuration register

Offset: 0x4, reset: 0x2022BB7F, access: read-write

0/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SYNCPOL rw		SYNCSRC rw			SYNCDIV rw			FELIM rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RELOAD rw

Toggle Fields.

RELOAD

Bits 0-15: Counter reload value.

FELIM

Bits 16-23: Frequency error limit.

SYNCDIV

Bits 24-26: SYNC divider.

SYNCSRC

Bits 28-29: SYNC signal source selection.

SYNCPOL

Bit 31: SYNC polarity selection.

ISR

interrupt and status register

Offset: 0x8, reset: 0x00000000, access: read-only

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FECAP r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FEDIR r					TRIMOVF r	SYNCMISS r	SYNCERR r					ESYNCF r	ERRF r	SYNCWARNF r	SYNCOKF r

Toggle Fields.

SYNCOKF

Bit 0: SYNC event OK flag.

SYNCWARNF

Bit 1: SYNC warning flag.

ERRF

Bit 2: Error flag.

ESYNCF

Bit 3: Expected SYNC flag.

SYNCERR

Bit 8: SYNC error.

SYNCMISS

Bit 9: SYNC missed.

TRIMOVF

Bit 10: Trimming overflow or underflow.

FEDIR

Bit 15: Frequency error direction.

FECAP

Bits 16-31: Frequency error capture.

ICR

interrupt flag clear register

Offset: 0xC, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												ESYNCC rw	ERRC rw	SYNCWARNC rw	SYNCOKC rw

Toggle Fields.

SYNCOKC

Bit 0: SYNC event OK clear flag.

SYNCWARNC

Bit 1: SYNC warning clear flag.

ERRC

Bit 2: Error clear flag.

ESYNCC

Bit 3: Expected SYNC clear flag.

DAC

0x40007400: Digital-to-analog converter

34/34 fields covered. Toggle Registers.

CR

control register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		DMAUDRIE2 rw	DMAEN2 rw	MAMP2 rw				WAVE2 rw		TSEL2 rw			TEN2 rw	BOFF2 rw	EN2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		DMAUDRIE1 rw	DMAEN1 rw	MAMP1 rw				WAVE1 rw		TSEL1 rw			TEN1 rw	BOFF1 rw	EN1 rw

Toggle Fields.

EN1

Bit 0: DAC channel1 enable.

Allowed values:
0: Disabled: DAC channel X disabled
1: Enabled: DAC channel X enabled

BOFF1

Bit 1: DAC channel1 output buffer disable.

Allowed values:
0: Enabled: DAC channel X output buffer enabled
1: Disabled: DAC channel X output buffer disabled

TEN1

Bit 2: DAC channel1 trigger enable.

Allowed values:
0: Disabled: DAC channel X trigger disabled
1: Enabled: DAC channel X trigger enabled

TSEL1

Bits 3-5: DAC channel1 trigger selection.

Allowed values:
0: TIM6_TRGO: Timer 6 TRGO event
1: TIM3_TRGO: Timer 3 TRGO event
2: TIM7_TRGO: Timer 7 TRGO event
3: TIM15_TRGO: Timer 15 TRGO event
4: TIM2_TRGO: Timer 2 TRGO event
6: EXTI9: EXTI line9
7: SOFTWARE: Software trigger

WAVE1

Bits 6-7: DAC channel1 noise/triangle wave generation enable.

Allowed values:
0: Disabled: Wave generation disabled
1: Noise: Noise wave generation enabled
2: Triangle: Triangle wave generation enabled

MAMP1

Bits 8-11: DAC channel1 mask/amplitude selector.

Allowed values: 0-15

DMAEN1

Bit 12: DAC channel1 DMA enable.

Allowed values:
0: Disabled: DAC channel X DMA mode disabled
1: Enabled: DAC channel X DMA mode enabled

DMAUDRIE1

Bit 13: DAC channel1 DMA Underrun Interrupt enable.

Allowed values:
0: Disabled: DAC channel X DMA Underrun Interrupt disabled
1: Enabled: DAC channel X DMA Underrun Interrupt enabled

EN2

Bit 16: DAC channel2 enable.

Allowed values:
0: Disabled: DAC channel X disabled
1: Enabled: DAC channel X enabled

BOFF2

Bit 17: DAC channel2 output buffer disable.

Allowed values:
0: Enabled: DAC channel X output buffer enabled
1: Disabled: DAC channel X output buffer disabled

TEN2

Bit 18: DAC channel2 trigger enable.

Allowed values:
0: Disabled: DAC channel X trigger disabled
1: Enabled: DAC channel X trigger enabled

TSEL2

Bits 19-21: DAC channel2 trigger selection.

Allowed values:
0: TIM6_TRGO: Timer 6 TRGO event
1: TIM8_TRGO: Timer 8 TRGO event
2: TIM7_TRGO: Timer 7 TRGO event
3: TIM5_TRGO: Timer 5 TRGO event
4: TIM2_TRGO: Timer 2 TRGO event
5: TIM4_TRGO: Timer 4 TRGO event
6: EXTI9: EXTI line9
7: SOFTWARE: Software trigger

WAVE2

Bits 22-23: DAC channel2 noise/triangle wave generation enable.

Allowed values:
0: Disabled: Wave generation disabled
1: Noise: Noise wave generation enabled
2: Triangle: Triangle wave generation enabled

MAMP2

Bits 24-27: DAC channel2 mask/amplitude selector.

Allowed values: 0-15

DMAEN2

Bit 28: DAC channel2 DMA enable.

Allowed values:
0: Disabled: DAC channel X DMA mode disabled
1: Enabled: DAC channel X DMA mode enabled

DMAUDRIE2

Bit 29: DAC channel2 DMA underrun interrupt enable.

Allowed values:
0: Disabled: DAC channel X DMA Underrun Interrupt disabled
1: Enabled: DAC channel X DMA Underrun Interrupt enabled

SWTRIGR

software trigger register

Offset: 0x4, reset: 0x00000000, access: write-only

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														SWTRIG2 w	SWTRIG1 w

Toggle Fields.

SWTRIG1

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								DACC2DHR rw

Toggle Fields.

DACC2DHR

Bits 0-7: DAC channel2 8-bit right-aligned data.

Allowed values: 0-255

DHR12RD

Offset: 0x20, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				DACC2DHR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC1DHR rw

Toggle Fields.

DACC1DHR

Bits 0-11: DAC channel1 12-bit right-aligned data.

Allowed values: 0-4096

DACC2DHR

Bits 16-27: DAC channel2 12-bit right-aligned data.

Allowed values: 0-4096

DHR12LD

Dual DAC 12-bit left-aligned data holding register

Offset: 0x24, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
DACC2DHR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DACC1DHR rw

Toggle Fields.

DACC1DHR

Bits 4-15: DAC channel1 12-bit left-aligned data.

Allowed values: 0-4096

DACC2DHR

Bits 20-31: DAC channel2 12-bit left-aligned data.

Allowed values: 0-4096

DHR8RD

Dual DAC 8-bit right-aligned data holding register

Offset: 0x28, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DACC2DHR rw								DACC1DHR rw

Toggle Fields.

DACC1DHR

Bits 0-7: DAC channel1 8-bit right-aligned data.

Allowed values: 0-255

DACC2DHR

Bits 8-15: DAC channel2 8-bit right-aligned data.

Allowed values: 0-255

DOR1

channel1 data output register

Offset: 0x2C, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC1DOR r

Toggle Fields.

DACC1DOR

Bits 0-11: DAC channel1 data output.

DOR2

DAC channel2 data output register

Offset: 0x30, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DACC2DOR r

Toggle Fields.

DACC2DOR

Bits 0-11: DAC channel2 data output.

SR

status register

Offset: 0x34, reset: 0x00000000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
		DMAUDR2 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		DMAUDR1 rw

Toggle Fields.

DMAUDR1

Bit 13: DAC channel1 DMA underrun flag.

Allowed values:
0: NoUnderrun: No DMA underrun error condition occurred for DAC channel X
1: Underrun: DMA underrun error condition occurred for DAC channel X

DMAUDR2

Bit 29: DAC channel2 DMA underrun flag.

Allowed values:
0: NoUnderrun: No DMA underrun error condition occurred for DAC channel X
1: Underrun: DMA underrun error condition occurred for DAC channel X

DBGMCU

0x40015800: Debug support

3/19 fields covered. Toggle Registers.

IDCODE

MCU Device ID Code Register

Offset: 0x0, reset: 0x0, access: read-only

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
REV_ID r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DIV_ID r				DEV_ID r

Toggle Fields.

DEV_ID

Bits 0-11: Device Identifier.

DIV_ID

Bits 12-15: Division Identifier.

REV_ID

Bits 16-31: Revision Identifier.

CR

Debug MCU Configuration Register

Offset: 0x4, reset: 0x0, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													DBG_STANDBY rw	DBG_STOP rw

Toggle Fields.

DBG_STOP

Bit 1: Debug Stop Mode.

DBG_STANDBY

Bit 2: Debug Standby Mode.

APB1_FZ

Debug MCU APB1 freeze register

Offset: 0x8, reset: 0x0, access: read-write

0/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						DBG_CAN_STOP rw				DBG_I2C1_SMBUS_TIMEOUT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBG_IWDG_STOP rw	DBG_WWDG_STOP rw	DBG_RTC_STOP rw		DBG_TIM14_STOP rw			DBG_TIM7_STOP rw	DBG_TIM6_STOP rw			DBG_TIM3_STOP rw	DBG_TIM2_STOP rw

Toggle Fields.

DBG_TIM2_STOP

Bit 0: TIM2 counter stopped when core is halted.

DBG_TIM3_STOP

Bit 1: TIM3 counter stopped when core is halted.

DBG_TIM6_STOP

Bit 4: TIM6 counter stopped when core is halted.

DBG_TIM7_STOP

Bit 5: TIM7 counter stopped when core is halted.

DBG_TIM14_STOP

Bit 8: TIM14 counter stopped when core is halted.

DBG_RTC_STOP

Bit 10: Debug RTC stopped when core is halted.

DBG_WWDG_STOP

Bit 11: Debug window watchdog stopped when core is halted.

DBG_IWDG_STOP

Bit 12: Debug independent watchdog stopped when core is halted.

DBG_I2C1_SMBUS_TIMEOUT

Bit 21: SMBUS timeout mode stopped when core is halted.

DBG_CAN_STOP

Bit 25: CAN stopped when core is halted.

APB2_FZ

Debug MCU APB2 freeze register

Offset: 0xC, reset: 0x0, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
													DBG_TIM17_STOP rw	DBG_TIM16_STOP rw	DBG_TIM15_STOP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				DBG_TIM1_STOP rw

Toggle Fields.

DBG_TIM1_STOP

Bit 11: TIM1 counter stopped when core is halted.

DBG_TIM15_STOP

Bit 16: TIM15 counter stopped when core is halted.

DBG_TIM16_STOP

Bit 17: TIM16 counter stopped when core is halted.

DBG_TIM17_STOP

Bit 18: TIM17 counter stopped when core is halted.

DMA1

0x40020000: DMA controller

69/71 fields covered. Toggle Registers.

CR

DMA channel configuration register (DMA_CCR)

Offset: 0x0, reset: 0x00000000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MEM2MEM rw	PL rw		MSIZE rw		PSIZE rw		MINC rw	PINC rw	CIRC rw	DIR rw	TEIE rw	HTIE rw	TCIE rw	EN rw

Toggle Fields.

EN

Bit 0: Channel enable.

Allowed values:
0: Disabled: Channel disabled
1: Enabled: Channel enabled

TCIE

Bit 1: Transfer complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

HTIE

Bit 2: Half Transfer interrupt enable.

Allowed values:
0: Disabled: Half Transfer interrupt disabled
1: Enabled: Half Transfer interrupt enabled

TEIE

Bit 3: Transfer error interrupt enable.

Allowed values:
0: Disabled: Transfer Error interrupt disabled
1: Enabled: Transfer Error interrupt enabled

DIR

Bit 4: Data transfer direction.

Allowed values:
0: FromPeripheral: Read from peripheral
1: FromMemory: Read from memory

CIRC

Bit 5: Circular mode.

Allowed values:
0: Disabled: Circular buffer disabled
1: Enabled: Circular buffer enabled

PINC

Bit 6: Peripheral increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

MINC

Bit 7: Memory increment mode.

Allowed values:
0: Disabled: Increment mode disabled
1: Enabled: Increment mode enabled

PSIZE

Bits 8-9: Peripheral size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

MSIZE

Bits 10-11: Memory size.

Allowed values:
0: Bits8: 8-bit size
1: Bits16: 16-bit size
2: Bits32: 32-bit size

PL

Bits 12-13: Channel Priority level.

Allowed values:
0: Low: Low priority
1: Medium: Medium priority
2: High: High priority
3: VeryHigh: Very high priority

MEM2MEM

Bit 14: Memory to memory mode.

Allowed values:
0: Disabled: Memory to memory mode disabled
1: Enabled: Memory to memory mode enabled

NDTR

DMA channel 1 number of data register

Offset: 0x4, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NDT rw

Toggle Fields.

NDT

Bits 0-15: Number of data to transfer.

Allowed values: 0-65535

PAR

DMA channel 1 peripheral address register

Offset: 0x8, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PA rw

Toggle Fields.

PA

Bits 0-31: Peripheral address.

MAR

DMA channel 1 memory address register

Offset: 0xC, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MA rw

Toggle Fields.

MA

Bits 0-31: Memory address.

EXTI

0x40010400: External interrupt/event controller

136/136 fields covered. Toggle Registers.

IMR

Interrupt mask register (EXTI_IMR)

Offset: 0x0, reset: 0x0F940000, access: read-write

28/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				MR27 rw	MR26 rw	MR25 rw	MR24 rw	MR23 rw	MR22 rw	MR21 rw	MR20 rw	MR19 rw	MR18 rw	MR17 rw	MR16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MR15 rw	MR14 rw	MR13 rw	MR12 rw	MR11 rw	MR10 rw	MR9 rw	MR8 rw	MR7 rw	MR6 rw	MR5 rw	MR4 rw	MR3 rw	MR2 rw	MR1 rw	MR0 rw

Toggle Fields.

MR0

Bit 0: Interrupt Mask on line 0.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR1

Bit 1: Interrupt Mask on line 1.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR2

Bit 2: Interrupt Mask on line 2.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR3

Bit 3: Interrupt Mask on line 3.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR4

Bit 4: Interrupt Mask on line 4.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR5

Bit 5: Interrupt Mask on line 5.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR6

Bit 6: Interrupt Mask on line 6.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR7

Bit 7: Interrupt Mask on line 7.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR8

Bit 8: Interrupt Mask on line 8.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR9

Bit 9: Interrupt Mask on line 9.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR10

Bit 10: Interrupt Mask on line 10.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR11

Bit 11: Interrupt Mask on line 11.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR12

Bit 12: Interrupt Mask on line 12.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR13

Bit 13: Interrupt Mask on line 13.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR14

Bit 14: Interrupt Mask on line 14.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR15

Bit 15: Interrupt Mask on line 15.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR16

Bit 16: Interrupt Mask on line 16.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR17

Bit 17: Interrupt Mask on line 17.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR18

Bit 18: Interrupt Mask on line 18.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR19

Bit 19: Interrupt Mask on line 19.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR20

Bit 20: Interrupt Mask on line 20.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR21

Bit 21: Interrupt Mask on line 21.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR22

Bit 22: Interrupt Mask on line 22.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR23

Bit 23: Interrupt Mask on line 23.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR24

Bit 24: Interrupt Mask on line 24.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR25

Bit 25: Interrupt Mask on line 25.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR26

Bit 26: Interrupt Mask on line 26.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR27

Bit 27: Interrupt Mask on line 27.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

EMR

Event mask register (EXTI_EMR)

Offset: 0x4, reset: 0x00000000, access: read-write

28/28 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				MR27 rw	MR26 rw	MR25 rw	MR24 rw	MR23 rw	MR22 rw	MR21 rw	MR20 rw	MR19 rw	MR18 rw	MR17 rw	MR16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MR15 rw	MR14 rw	MR13 rw	MR12 rw	MR11 rw	MR10 rw	MR9 rw	MR8 rw	MR7 rw	MR6 rw	MR5 rw	MR4 rw	MR3 rw	MR2 rw	MR1 rw	MR0 rw

Toggle Fields.

MR0

Bit 0: Event Mask on line 0.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR1

Bit 1: Event Mask on line 1.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR2

Bit 2: Event Mask on line 2.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR3

Bit 3: Event Mask on line 3.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR4

Bit 4: Event Mask on line 4.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR5

Bit 5: Event Mask on line 5.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR6

Bit 6: Event Mask on line 6.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR7

Bit 7: Event Mask on line 7.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR8

Bit 8: Event Mask on line 8.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR9

Bit 9: Event Mask on line 9.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR10

Bit 10: Event Mask on line 10.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR11

Bit 11: Event Mask on line 11.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR12

Bit 12: Event Mask on line 12.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR13

Bit 13: Event Mask on line 13.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR14

Bit 14: Event Mask on line 14.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR15

Bit 15: Event Mask on line 15.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR16

Bit 16: Event Mask on line 16.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR17

Bit 17: Event Mask on line 17.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR18

Bit 18: Event Mask on line 18.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR19

Bit 19: Event Mask on line 19.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR20

Bit 20: Event Mask on line 20.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR21

Bit 21: Event Mask on line 21.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR22

Bit 22: Event Mask on line 22.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR23

Bit 23: Event Mask on line 23.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR24

Bit 24: Event Mask on line 24.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR25

Bit 25: Event Mask on line 25.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR26

Bit 26: Event Mask on line 26.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

MR27

Bit 27: Event Mask on line 27.

Allowed values:
0: Masked: Interrupt request line is masked
1: Unmasked: Interrupt request line is unmasked

RTSR

Rising Trigger selection register (EXTI_RTSR)

Offset: 0x8, reset: 0x00000000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												TR19 rw		TR17 rw	TR16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TR15 rw	TR14 rw	TR13 rw	TR12 rw	TR11 rw	TR10 rw	TR9 rw	TR8 rw	TR7 rw	TR6 rw	TR5 rw	TR4 rw	TR3 rw	TR2 rw	TR1 rw	TR0 rw

Toggle Fields.

TR0

Bit 0: Rising trigger event configuration of line 0.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR1

Bit 1: Rising trigger event configuration of line 1.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR2

Bit 2: Rising trigger event configuration of line 2.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR3

Bit 3: Rising trigger event configuration of line 3.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR4

Bit 4: Rising trigger event configuration of line 4.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR5

Bit 5: Rising trigger event configuration of line 5.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR6

Bit 6: Rising trigger event configuration of line 6.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR7

Bit 7: Rising trigger event configuration of line 7.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR8

Bit 8: Rising trigger event configuration of line 8.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR9

Bit 9: Rising trigger event configuration of line 9.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR10

Bit 10: Rising trigger event configuration of line 10.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR11

Bit 11: Rising trigger event configuration of line 11.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR12

Bit 12: Rising trigger event configuration of line 12.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR13

Bit 13: Rising trigger event configuration of line 13.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR14

Bit 14: Rising trigger event configuration of line 14.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR15

Bit 15: Rising trigger event configuration of line 15.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR16

Bit 16: Rising trigger event configuration of line 16.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR17

Bit 17: Rising trigger event configuration of line 17.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

TR19

Bit 19: Rising trigger event configuration of line 19.

Allowed values:
0: Disabled: Rising edge trigger is disabled
1: Enabled: Rising edge trigger is enabled

FTSR

Falling Trigger selection register (EXTI_FTSR)

Offset: 0xC, reset: 0x00000000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												TR19 rw		TR17 rw	TR16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TR15 rw	TR14 rw	TR13 rw	TR12 rw	TR11 rw	TR10 rw	TR9 rw	TR8 rw	TR7 rw	TR6 rw	TR5 rw	TR4 rw	TR3 rw	TR2 rw	TR1 rw	TR0 rw

Toggle Fields.

TR0

Bit 0: Falling trigger event configuration of line 0.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR1

Bit 1: Falling trigger event configuration of line 1.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR2

Bit 2: Falling trigger event configuration of line 2.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR3

Bit 3: Falling trigger event configuration of line 3.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR4

Bit 4: Falling trigger event configuration of line 4.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR5

Bit 5: Falling trigger event configuration of line 5.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR6

Bit 6: Falling trigger event configuration of line 6.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR7

Bit 7: Falling trigger event configuration of line 7.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR8

Bit 8: Falling trigger event configuration of line 8.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR9

Bit 9: Falling trigger event configuration of line 9.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR10

Bit 10: Falling trigger event configuration of line 10.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR11

Bit 11: Falling trigger event configuration of line 11.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR12

Bit 12: Falling trigger event configuration of line 12.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR13

Bit 13: Falling trigger event configuration of line 13.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR14

Bit 14: Falling trigger event configuration of line 14.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR15

Bit 15: Falling trigger event configuration of line 15.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR16

Bit 16: Falling trigger event configuration of line 16.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR17

Bit 17: Falling trigger event configuration of line 17.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

TR19

Bit 19: Falling trigger event configuration of line 19.

Allowed values:
0: Disabled: Falling edge trigger is disabled
1: Enabled: Falling edge trigger is enabled

SWIER

Software interrupt event register (EXTI_SWIER)

Offset: 0x10, reset: 0x00000000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												SWIER19 rw		SWIER17 rw	SWIER16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWIER15 rw	SWIER14 rw	SWIER13 rw	SWIER12 rw	SWIER11 rw	SWIER10 rw	SWIER9 rw	SWIER8 rw	SWIER7 rw	SWIER6 rw	SWIER5 rw	SWIER4 rw	SWIER3 rw	SWIER2 rw	SWIER1 rw	SWIER0 rw

Toggle Fields.

SWIER0

Bit 0: Software Interrupt on line 0.

Allowed values:
1: Pend: Generates an interrupt request

SWIER1

Bit 1: Software Interrupt on line 1.

Allowed values:
1: Pend: Generates an interrupt request

SWIER2

Bit 2: Software Interrupt on line 2.

Allowed values:
1: Pend: Generates an interrupt request

SWIER3

Bit 3: Software Interrupt on line 3.

Allowed values:
1: Pend: Generates an interrupt request

SWIER4

Bit 4: Software Interrupt on line 4.

Allowed values:
1: Pend: Generates an interrupt request

SWIER5

Bit 5: Software Interrupt on line 5.

Allowed values:
1: Pend: Generates an interrupt request

SWIER6

Bit 6: Software Interrupt on line 6.

Allowed values:
1: Pend: Generates an interrupt request

SWIER7

Bit 7: Software Interrupt on line 7.

Allowed values:
1: Pend: Generates an interrupt request

SWIER8

Bit 8: Software Interrupt on line 8.

Allowed values:
1: Pend: Generates an interrupt request

SWIER9

Bit 9: Software Interrupt on line 9.

Allowed values:
1: Pend: Generates an interrupt request

SWIER10

Bit 10: Software Interrupt on line 10.

Allowed values:
1: Pend: Generates an interrupt request

SWIER11

Bit 11: Software Interrupt on line 11.

Allowed values:
1: Pend: Generates an interrupt request

SWIER12

Bit 12: Software Interrupt on line 12.

Allowed values:
1: Pend: Generates an interrupt request

SWIER13

Bit 13: Software Interrupt on line 13.

Allowed values:
1: Pend: Generates an interrupt request

SWIER14

Bit 14: Software Interrupt on line 14.

Allowed values:
1: Pend: Generates an interrupt request

SWIER15

Bit 15: Software Interrupt on line 15.

Allowed values:
1: Pend: Generates an interrupt request

SWIER16

Bit 16: Software Interrupt on line 16.

Allowed values:
1: Pend: Generates an interrupt request

SWIER17

Bit 17: Software Interrupt on line 17.

Allowed values:
1: Pend: Generates an interrupt request

SWIER19

Bit 19: Software Interrupt on line 19.

Allowed values:
1: Pend: Generates an interrupt request

PR

Pending register (EXTI_PR)

Offset: 0x14, reset: 0x00000000, access: read-write

23/23 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PIF31 rw									PIF22 rw	PIF21 rw	PIF20 rw	PIF19 rw		PIF17 rw	PIF16 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PIF15 rw	PIF14 rw	PIF13 rw	PIF12 rw	PIF11 rw	PIF10 rw	PIF9 rw	PIF8 rw	PIF7 rw	PIF6 rw	PIF5 rw	PIF4 rw	PIF3 rw	PIF2 rw	PIF1 rw	PIF0 rw

Toggle Fields.

PIF0

Bit 0: Pending interrupt flag on line 0.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF1

Bit 1: Pending interrupt flag on line 1.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF2

Bit 2: Pending interrupt flag on line 2.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF3

Bit 3: Pending interrupt flag on line 3.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF4

Bit 4: Pending interrupt flag on line 4.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF5

Bit 5: Pending interrupt flag on line 5.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF6

Bit 6: Pending interrupt flag on line 6.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF7

Bit 7: Pending interrupt flag on line 7.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF8

Bit 8: Pending interrupt flag on line 8.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF9

Bit 9: Pending interrupt flag on line 9.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF10

Bit 10: Pending interrupt flag on line 10.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF11

Bit 11: Pending interrupt flag on line 11.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF12

Bit 12: Pending interrupt flag on line 12.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF13

Bit 13: Pending interrupt flag on line 13.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF14

Bit 14: Pending interrupt flag on line 14.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF15

Bit 15: Pending interrupt flag on line 15.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF16

Bit 16: Pending interrupt flag on line 16.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF17

Bit 17: Pending interrupt flag on line 17.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF19

Bit 19: Pending interrupt flag on line 19.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF20

Bit 20: Pending interrupt flag on line 20.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF21

Bit 21: Pending interrupt flag on line 21.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF22

Bit 22: Pending interrupt flag on line 22.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

PIF31

Bit 31: Pending interrupt flag on line 31.

Allowed values:
0: NotPending: No trigger request occurred
1: Pending: Selected trigger request occurred

Flash

0x40022000: Flash

34/34 fields covered. Toggle Registers.

ACR

Flash access control register

Offset: 0x0, reset: 0x00000030, access: Unspecified

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										PRFTBS r	PRFTBE rw		LATENCY rw

Toggle Fields.

LATENCY

Bits 0-2: LATENCY.

Allowed values:
0: WS0: 0 wait states
1: WS1: 1 wait state

PRFTBE

Bit 4: PRFTBE.

Allowed values:
0: Disabled: Prefetch is disabled
1: Enabled: Prefetch is enabled

PRFTBS

Bit 5: PRFTBS.

Allowed values:
0: Disabled: Prefetch buffer is disabled
1: Enabled: Prefetch buffer is enabled

KEYR

Flash key register

Offset: 0x4, reset: 0x00000000, access: write-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FKEYR w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FKEYR w

Toggle Fields.

FKEYR

Bits 0-31: Flash Key.

Allowed values: 0-4294967295

OPTKEYR

Flash option key register

Offset: 0x8, reset: 0x00000000, access: write-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OPTKEYR w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OPTKEYR w

Toggle Fields.

OPTKEYR

Bits 0-31: Option byte key.

Allowed values: 0-4294967295

SR

Flash status register

Offset: 0xC, reset: 0x00000000, access: Unspecified

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
										EOP rw	WRPRT rw		PGERR rw		BSY r

Toggle Fields.

BSY

Bit 0: Busy.

Allowed values:
0: Inactive: No write/erase operation is in progress
1: Active: No write/erase operation is in progress

PGERR

Bit 2: Programming error.

Allowed values:
0: NoError: No programming error occurred
1: Error: A programming error occurred

WRPRT

Bit 4: Write protection error.

Allowed values:
0: NoError: No write protection error occurred
1: Error: A write protection error occurred

EOP

Bit 5: End of operation.

Allowed values:
0: NoEvent: No EOP operation occurred
1: Event: An EOP event occurred

CR

Flash control register

Offset: 0x10, reset: 0x00000080, access: read-write

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		FORCE_OPTLOAD rw	EOPIE rw		ERRIE rw	OPTWRE rw		LOCK rw	STRT rw	OPTER rw	OPTPG rw		MER rw	PER rw	PG rw

Toggle Fields.

PG

Bit 0: Programming.

Allowed values:
1: Program: Flash programming activated

PER

Bit 1: Page erase.

Allowed values:
1: PageErase: Erase activated for selected page

MER

Bit 2: Mass erase.

Allowed values:
1: MassErase: Erase activated for all user sectors

OPTPG

Bit 4: Option byte programming.

Allowed values:
1: OptionByteProgramming: Program option byte activated

OPTER

Bit 5: Option byte erase.

Allowed values:
1: OptionByteErase: Erase option byte activated

STRT

Bit 6: Start.

Allowed values:
1: Start: Trigger an erase operation

LOCK

Bit 7: Lock.

Allowed values:
0: Unlocked: FLASH_CR register is unlocked
1: Locked: FLASH_CR register is locked

OPTWRE

Bit 9: Option bytes write enable.

Allowed values:
0: Disabled: Option byte write enabled
1: Enabled: Option byte write disabled

ERRIE

Bit 10: Error interrupt enable.

Allowed values:
0: Disabled: Error interrupt generation disabled
1: Enabled: Error interrupt generation enabled

EOPIE

Bit 12: End of operation interrupt enable.

Allowed values:
0: Disabled: End of operation interrupt disabled
1: Enabled: End of operation interrupt enabled

FORCE_OPTLOAD

Bit 13: Force option byte loading.

Allowed values:
0: Inactive: Force option byte loading inactive
1: Active: Force option byte loading active

AR

Flash address register

Offset: 0x14, reset: 0x00000000, access: write-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
FAR w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
FAR w

Toggle Fields.

FAR

Bits 0-31: Flash address.

Allowed values: 0-4294967295

OBR

Option byte register

Offset: 0x1C, reset: 0x03FFFFF2, access: read-only

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
Data1 r								Data0 r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BOOT_SEL r	RAM_PARITY_CHECK r	VDDA_MONITOR r	nBOOT1 r	nBOOT0 r	nRST_STDBY r	nRST_STOP r	WDG_SW r						RDPRT r		OPTERR r

Toggle Fields.

OPTERR

Bit 0: Option byte error.

Allowed values:
1: OptionByteError: The loaded option byte and its complement do not match

RDPRT

Bits 1-2: Read protection level status.

Allowed values:
0: Level0: Level 0
1: Level1: Level 1
3: Level2: Level 2

WDG_SW

Bit 8: WDG_SW.

Allowed values:
0: Hardware: Hardware watchdog
1: Software: Software watchdog

nRST_STOP

Bit 9: nRST_STOP.

Allowed values:
0: Reset: Reset generated when entering Stop mode
1: NoReset: No reset generated

nRST_STDBY

Bit 10: nRST_STDBY.

Allowed values:
0: Reset: Reset generated when entering Standby mode
1: NoReset: No reset generated

nBOOT0

Bit 11: nBOOT0.

Allowed values:
0: Disabled: When BOOT_SEL is cleared, select the device boot mode
1: Enabled: When BOOT_SEL is cleared, select the device boot mode

nBOOT1

Bit 12: BOOT1.

Allowed values:
0: Disabled: Together with BOOT0, select the device boot mode
1: Enabled: Together with BOOT0, select the device boot mode

VDDA_MONITOR

Bit 13: VDDA_MONITOR.

Allowed values:
0: Disabled: VDDA power supply supervisor disabled
1: Enabled: VDDA power supply supervisor enabled

RAM_PARITY_CHECK

Bit 14: RAM_PARITY_CHECK.

Allowed values:
1: Disabled: RAM parity check disabled
0: Enabled: RAM parity check enabled

BOOT_SEL

Bit 15: BOOT_SEL.

Allowed values:
0: nBOOT0: BOOT0 signal is defined by nBOOT0 option bit
1: BOOT0: BOOT0 signal is defined by BOOT0 pin value (legacy mode)

Data0

Bits 16-23: Data0.

Allowed values: 0-255

Data1

Bits 24-31: Data1.

Allowed values: 0-255

WRPR

Write protection register

Offset: 0x20, reset: 0xFFFFFFFF, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
WRP r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
WRP r

Toggle Fields.

WRP

Bits 0-31: Write protect.

Allowed values: 0-4294967295

GPIOA

0x48000000: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x28000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER15 rw		MODER14 rw		MODER13 rw		MODER12 rw		MODER11 rw		MODER10 rw		MODER9 rw		MODER8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER7 rw		MODER6 rw		MODER5 rw		MODER4 rw		MODER3 rw		MODER2 rw		MODER1 rw		MODER0 rw

Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT15 rw	OT14 rw	OT13 rw	OT12 rw	OT11 rw	OT10 rw	OT9 rw	OT8 rw	OT7 rw	OT6 rw	OT5 rw	OT4 rw	OT3 rw	OT2 rw	OT1 rw	OT0 rw

Toggle Fields.

OT0

Bit 0: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bits (y = 0..15).

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR15 rw		OSPEEDR14 rw		OSPEEDR13 rw		OSPEEDR12 rw		OSPEEDR11 rw		OSPEEDR10 rw		OSPEEDR9 rw		OSPEEDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR7 rw		OSPEEDR6 rw		OSPEEDR5 rw		OSPEEDR4 rw		OSPEEDR3 rw		OSPEEDR2 rw		OSPEEDR1 rw		OSPEEDR0 rw

Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x24000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR15 rw		PUPDR14 rw		PUPDR13 rw		PUPDR12 rw		PUPDR11 rw		PUPDR10 rw		PUPDR9 rw		PUPDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR7 rw		PUPDR6 rw		PUPDR5 rw		PUPDR4 rw		PUPDR3 rw		PUPDR2 rw		PUPDR1 rw		PUPDR0 rw

Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR15 r	IDR14 r	IDR13 r	IDR12 r	IDR11 r	IDR10 r	IDR9 r	IDR8 r	IDR7 r	IDR6 r	IDR5 r	IDR4 r	IDR3 r	IDR2 r	IDR1 r	IDR0 r

Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR15 rw	ODR14 rw	ODR13 rw	ODR12 rw	ODR11 rw	ODR10 rw	ODR9 rw	ODR8 rw	ODR7 rw	ODR6 rw	ODR5 rw	ODR4 rw	ODR3 rw	ODR2 rw	ODR1 rw	ODR0 rw

Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS15 w	BS14 w	BS13 w	BS12 w	BS11 w	BS10 w	BS9 w	BS8 w	BS7 w	BS6 w	BS5 w	BS4 w	BS3 w	BS2 w	BS1 w	BS0 w

Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK15 rw	LCK14 rw	LCK13 rw	LCK12 rw	LCK11 rw	LCK10 rw	LCK9 rw	LCK8 rw	LCK7 rw	LCK6 rw	LCK5 rw	LCK4 rw	LCK3 rw	LCK2 rw	LCK1 rw	LCK0 rw

Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Port x lock bit y (y= 0..15).

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRL7 rw				AFRL6 rw				AFRL5 rw				AFRL4 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRL3 rw				AFRL2 rw				AFRL1 rw				AFRL0 rw

Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

Allowed values:
0: AF0: AF0
1: AF1: AF1
2: AF2: AF2
3: AF3: AF3
4: AF4: AF4
5: AF5: AF5
6: AF6: AF6
7: AF7: AF7
8: AF8: AF8
9: AF9: AF9
10: AF10: AF10
11: AF11: AF11
12: AF12: AF12
13: AF13: AF13
14: AF14: AF14
15: AF15: AF15

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRH15 rw				AFRH14 rw				AFRH13 rw				AFRH12 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRH11 rw				AFRH10 rw				AFRH9 rw				AFRH8 rw

Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w

Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOB

0x48000400: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER15 rw		MODER14 rw		MODER13 rw		MODER12 rw		MODER11 rw		MODER10 rw		MODER9 rw		MODER8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER7 rw		MODER6 rw		MODER5 rw		MODER4 rw		MODER3 rw		MODER2 rw		MODER1 rw		MODER0 rw

Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT15 rw	OT14 rw	OT13 rw	OT12 rw	OT11 rw	OT10 rw	OT9 rw	OT8 rw	OT7 rw	OT6 rw	OT5 rw	OT4 rw	OT3 rw	OT2 rw	OT1 rw	OT0 rw

Toggle Fields.

OT0

Bit 0: Port x configuration bit 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bit 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bit 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bit 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bit 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bit 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bit 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bit 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bit 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bit 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bit 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bit 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bit 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bit 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bit 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bit 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR15 rw		OSPEEDR14 rw		OSPEEDR13 rw		OSPEEDR12 rw		OSPEEDR11 rw		OSPEEDR10 rw		OSPEEDR9 rw		OSPEEDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR7 rw		OSPEEDR6 rw		OSPEEDR5 rw		OSPEEDR4 rw		OSPEEDR3 rw		OSPEEDR2 rw		OSPEEDR1 rw		OSPEEDR0 rw

Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR15 rw		PUPDR14 rw		PUPDR13 rw		PUPDR12 rw		PUPDR11 rw		PUPDR10 rw		PUPDR9 rw		PUPDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR7 rw		PUPDR6 rw		PUPDR5 rw		PUPDR4 rw		PUPDR3 rw		PUPDR2 rw		PUPDR1 rw		PUPDR0 rw

Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR15 r	IDR14 r	IDR13 r	IDR12 r	IDR11 r	IDR10 r	IDR9 r	IDR8 r	IDR7 r	IDR6 r	IDR5 r	IDR4 r	IDR3 r	IDR2 r	IDR1 r	IDR0 r

Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR15 rw	ODR14 rw	ODR13 rw	ODR12 rw	ODR11 rw	ODR10 rw	ODR9 rw	ODR8 rw	ODR7 rw	ODR6 rw	ODR5 rw	ODR4 rw	ODR3 rw	ODR2 rw	ODR1 rw	ODR0 rw

Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS15 w	BS14 w	BS13 w	BS12 w	BS11 w	BS10 w	BS9 w	BS8 w	BS7 w	BS6 w	BS5 w	BS4 w	BS3 w	BS2 w	BS1 w	BS0 w

Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK15 rw	LCK14 rw	LCK13 rw	LCK12 rw	LCK11 rw	LCK10 rw	LCK9 rw	LCK8 rw	LCK7 rw	LCK6 rw	LCK5 rw	LCK4 rw	LCK3 rw	LCK2 rw	LCK1 rw	LCK0 rw

Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Port x lock bit y.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRL7 rw				AFRL6 rw				AFRL5 rw				AFRL4 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRL3 rw				AFRL2 rw				AFRL1 rw				AFRL0 rw

Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRH15 rw				AFRH14 rw				AFRH13 rw				AFRH12 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRH11 rw				AFRH10 rw				AFRH9 rw				AFRH8 rw

Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w

Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOC

0x48000800: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER15 rw		MODER14 rw		MODER13 rw		MODER12 rw		MODER11 rw		MODER10 rw		MODER9 rw		MODER8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER7 rw		MODER6 rw		MODER5 rw		MODER4 rw		MODER3 rw		MODER2 rw		MODER1 rw		MODER0 rw

Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT15 rw	OT14 rw	OT13 rw	OT12 rw	OT11 rw	OT10 rw	OT9 rw	OT8 rw	OT7 rw	OT6 rw	OT5 rw	OT4 rw	OT3 rw	OT2 rw	OT1 rw	OT0 rw

Toggle Fields.

OT0

Bit 0: Port x configuration bit 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bit 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bit 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bit 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bit 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bit 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bit 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bit 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bit 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bit 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bit 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bit 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bit 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bit 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bit 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bit 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR15 rw		OSPEEDR14 rw		OSPEEDR13 rw		OSPEEDR12 rw		OSPEEDR11 rw		OSPEEDR10 rw		OSPEEDR9 rw		OSPEEDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR7 rw		OSPEEDR6 rw		OSPEEDR5 rw		OSPEEDR4 rw		OSPEEDR3 rw		OSPEEDR2 rw		OSPEEDR1 rw		OSPEEDR0 rw

Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR15 rw		PUPDR14 rw		PUPDR13 rw		PUPDR12 rw		PUPDR11 rw		PUPDR10 rw		PUPDR9 rw		PUPDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR7 rw		PUPDR6 rw		PUPDR5 rw		PUPDR4 rw		PUPDR3 rw		PUPDR2 rw		PUPDR1 rw		PUPDR0 rw

Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR15 r	IDR14 r	IDR13 r	IDR12 r	IDR11 r	IDR10 r	IDR9 r	IDR8 r	IDR7 r	IDR6 r	IDR5 r	IDR4 r	IDR3 r	IDR2 r	IDR1 r	IDR0 r

Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR15 rw	ODR14 rw	ODR13 rw	ODR12 rw	ODR11 rw	ODR10 rw	ODR9 rw	ODR8 rw	ODR7 rw	ODR6 rw	ODR5 rw	ODR4 rw	ODR3 rw	ODR2 rw	ODR1 rw	ODR0 rw

Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS15 w	BS14 w	BS13 w	BS12 w	BS11 w	BS10 w	BS9 w	BS8 w	BS7 w	BS6 w	BS5 w	BS4 w	BS3 w	BS2 w	BS1 w	BS0 w

Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK15 rw	LCK14 rw	LCK13 rw	LCK12 rw	LCK11 rw	LCK10 rw	LCK9 rw	LCK8 rw	LCK7 rw	LCK6 rw	LCK5 rw	LCK4 rw	LCK3 rw	LCK2 rw	LCK1 rw	LCK0 rw

Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Port x lock bit y.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRL7 rw				AFRL6 rw				AFRL5 rw				AFRL4 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRL3 rw				AFRL2 rw				AFRL1 rw				AFRL0 rw

Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRH15 rw				AFRH14 rw				AFRH13 rw				AFRH12 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRH11 rw				AFRH10 rw				AFRH9 rw				AFRH8 rw

Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w

Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOD

0x48000C00: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER15 rw		MODER14 rw		MODER13 rw		MODER12 rw		MODER11 rw		MODER10 rw		MODER9 rw		MODER8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER7 rw		MODER6 rw		MODER5 rw		MODER4 rw		MODER3 rw		MODER2 rw		MODER1 rw		MODER0 rw

Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT15 rw	OT14 rw	OT13 rw	OT12 rw	OT11 rw	OT10 rw	OT9 rw	OT8 rw	OT7 rw	OT6 rw	OT5 rw	OT4 rw	OT3 rw	OT2 rw	OT1 rw	OT0 rw

Toggle Fields.

OT0

Bit 0: Port x configuration bit 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bit 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bit 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bit 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bit 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bit 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bit 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bit 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bit 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bit 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bit 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bit 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bit 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bit 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bit 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bit 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR15 rw		OSPEEDR14 rw		OSPEEDR13 rw		OSPEEDR12 rw		OSPEEDR11 rw		OSPEEDR10 rw		OSPEEDR9 rw		OSPEEDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR7 rw		OSPEEDR6 rw		OSPEEDR5 rw		OSPEEDR4 rw		OSPEEDR3 rw		OSPEEDR2 rw		OSPEEDR1 rw		OSPEEDR0 rw

Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR15 rw		PUPDR14 rw		PUPDR13 rw		PUPDR12 rw		PUPDR11 rw		PUPDR10 rw		PUPDR9 rw		PUPDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR7 rw		PUPDR6 rw		PUPDR5 rw		PUPDR4 rw		PUPDR3 rw		PUPDR2 rw		PUPDR1 rw		PUPDR0 rw

Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR15 r	IDR14 r	IDR13 r	IDR12 r	IDR11 r	IDR10 r	IDR9 r	IDR8 r	IDR7 r	IDR6 r	IDR5 r	IDR4 r	IDR3 r	IDR2 r	IDR1 r	IDR0 r

Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR15 rw	ODR14 rw	ODR13 rw	ODR12 rw	ODR11 rw	ODR10 rw	ODR9 rw	ODR8 rw	ODR7 rw	ODR6 rw	ODR5 rw	ODR4 rw	ODR3 rw	ODR2 rw	ODR1 rw	ODR0 rw

Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS15 w	BS14 w	BS13 w	BS12 w	BS11 w	BS10 w	BS9 w	BS8 w	BS7 w	BS6 w	BS5 w	BS4 w	BS3 w	BS2 w	BS1 w	BS0 w

Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK15 rw	LCK14 rw	LCK13 rw	LCK12 rw	LCK11 rw	LCK10 rw	LCK9 rw	LCK8 rw	LCK7 rw	LCK6 rw	LCK5 rw	LCK4 rw	LCK3 rw	LCK2 rw	LCK1 rw	LCK0 rw

Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Port x lock bit y.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRL7 rw				AFRL6 rw				AFRL5 rw				AFRL4 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRL3 rw				AFRL2 rw				AFRL1 rw				AFRL0 rw

Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRH15 rw				AFRH14 rw				AFRH13 rw				AFRH12 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRH11 rw				AFRH10 rw				AFRH9 rw				AFRH8 rw

Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w

Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOE

0x48001000: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER15 rw		MODER14 rw		MODER13 rw		MODER12 rw		MODER11 rw		MODER10 rw		MODER9 rw		MODER8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER7 rw		MODER6 rw		MODER5 rw		MODER4 rw		MODER3 rw		MODER2 rw		MODER1 rw		MODER0 rw

Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT15 rw	OT14 rw	OT13 rw	OT12 rw	OT11 rw	OT10 rw	OT9 rw	OT8 rw	OT7 rw	OT6 rw	OT5 rw	OT4 rw	OT3 rw	OT2 rw	OT1 rw	OT0 rw

Toggle Fields.

OT0

Bit 0: Port x configuration bit 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bit 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bit 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bit 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bit 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bit 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bit 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bit 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bit 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bit 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bit 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bit 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bit 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bit 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bit 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bit 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR15 rw		OSPEEDR14 rw		OSPEEDR13 rw		OSPEEDR12 rw		OSPEEDR11 rw		OSPEEDR10 rw		OSPEEDR9 rw		OSPEEDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR7 rw		OSPEEDR6 rw		OSPEEDR5 rw		OSPEEDR4 rw		OSPEEDR3 rw		OSPEEDR2 rw		OSPEEDR1 rw		OSPEEDR0 rw

Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR15 rw		PUPDR14 rw		PUPDR13 rw		PUPDR12 rw		PUPDR11 rw		PUPDR10 rw		PUPDR9 rw		PUPDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR7 rw		PUPDR6 rw		PUPDR5 rw		PUPDR4 rw		PUPDR3 rw		PUPDR2 rw		PUPDR1 rw		PUPDR0 rw

Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR15 r	IDR14 r	IDR13 r	IDR12 r	IDR11 r	IDR10 r	IDR9 r	IDR8 r	IDR7 r	IDR6 r	IDR5 r	IDR4 r	IDR3 r	IDR2 r	IDR1 r	IDR0 r

Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR15 rw	ODR14 rw	ODR13 rw	ODR12 rw	ODR11 rw	ODR10 rw	ODR9 rw	ODR8 rw	ODR7 rw	ODR6 rw	ODR5 rw	ODR4 rw	ODR3 rw	ODR2 rw	ODR1 rw	ODR0 rw

Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS15 w	BS14 w	BS13 w	BS12 w	BS11 w	BS10 w	BS9 w	BS8 w	BS7 w	BS6 w	BS5 w	BS4 w	BS3 w	BS2 w	BS1 w	BS0 w

Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK15 rw	LCK14 rw	LCK13 rw	LCK12 rw	LCK11 rw	LCK10 rw	LCK9 rw	LCK8 rw	LCK7 rw	LCK6 rw	LCK5 rw	LCK4 rw	LCK3 rw	LCK2 rw	LCK1 rw	LCK0 rw

Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Port x lock bit y.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRL7 rw				AFRL6 rw				AFRL5 rw				AFRL4 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRL3 rw				AFRL2 rw				AFRL1 rw				AFRL0 rw

Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRH15 rw				AFRH14 rw				AFRH13 rw				AFRH12 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRH11 rw				AFRH10 rw				AFRH9 rw				AFRH8 rw

Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w

Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

GPIOF

0x48001400: General-purpose I/Os

177/177 fields covered. Toggle Registers.

MODER

GPIO port mode register

Offset: 0x0, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MODER15 rw		MODER14 rw		MODER13 rw		MODER12 rw		MODER11 rw		MODER10 rw		MODER9 rw		MODER8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MODER7 rw		MODER6 rw		MODER5 rw		MODER4 rw		MODER3 rw		MODER2 rw		MODER1 rw		MODER0 rw

Toggle Fields.

MODER0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

MODER15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Input: Input mode (reset state)
1: Output: General purpose output mode
2: Alternate: Alternate function mode
3: Analog: Analog mode

OTYPER

GPIO port output type register

Offset: 0x4, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OT15 rw	OT14 rw	OT13 rw	OT12 rw	OT11 rw	OT10 rw	OT9 rw	OT8 rw	OT7 rw	OT6 rw	OT5 rw	OT4 rw	OT3 rw	OT2 rw	OT1 rw	OT0 rw

Toggle Fields.

OT0

Bit 0: Port x configuration bit 0.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT1

Bit 1: Port x configuration bit 1.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT2

Bit 2: Port x configuration bit 2.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT3

Bit 3: Port x configuration bit 3.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT4

Bit 4: Port x configuration bit 4.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT5

Bit 5: Port x configuration bit 5.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT6

Bit 6: Port x configuration bit 6.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT7

Bit 7: Port x configuration bit 7.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT8

Bit 8: Port x configuration bit 8.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT9

Bit 9: Port x configuration bit 9.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT10

Bit 10: Port x configuration bit 10.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT11

Bit 11: Port x configuration bit 11.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT12

Bit 12: Port x configuration bit 12.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT13

Bit 13: Port x configuration bit 13.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT14

Bit 14: Port x configuration bit 14.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OT15

Bit 15: Port x configuration bit 15.

Allowed values:
0: PushPull: Output push-pull (reset state)
1: OpenDrain: Output open-drain

OSPEEDR

GPIO port output speed register

Offset: 0x8, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
OSPEEDR15 rw		OSPEEDR14 rw		OSPEEDR13 rw		OSPEEDR12 rw		OSPEEDR11 rw		OSPEEDR10 rw		OSPEEDR9 rw		OSPEEDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OSPEEDR7 rw		OSPEEDR6 rw		OSPEEDR5 rw		OSPEEDR4 rw		OSPEEDR3 rw		OSPEEDR2 rw		OSPEEDR1 rw		OSPEEDR0 rw

Toggle Fields.

OSPEEDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

OSPEEDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: LowSpeed: Low speed
1: MediumSpeed: Medium speed
2: HighSpeed: High speed
3: VeryHighSpeed: Very high speed

PUPDR

GPIO port pull-up/pull-down register

Offset: 0xC, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PUPDR15 rw		PUPDR14 rw		PUPDR13 rw		PUPDR12 rw		PUPDR11 rw		PUPDR10 rw		PUPDR9 rw		PUPDR8 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PUPDR7 rw		PUPDR6 rw		PUPDR5 rw		PUPDR4 rw		PUPDR3 rw		PUPDR2 rw		PUPDR1 rw		PUPDR0 rw

Toggle Fields.

PUPDR0

Bits 0-1: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR1

Bits 2-3: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR2

Bits 4-5: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR3

Bits 6-7: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR4

Bits 8-9: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR5

Bits 10-11: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR6

Bits 12-13: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR7

Bits 14-15: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR8

Bits 16-17: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR9

Bits 18-19: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR10

Bits 20-21: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR11

Bits 22-23: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR12

Bits 24-25: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR13

Bits 26-27: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR14

Bits 28-29: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

PUPDR15

Bits 30-31: Port x configuration bits (y = 0..15).

Allowed values:
0: Floating: No pull-up, pull-down
1: PullUp: Pull-up
2: PullDown: Pull-down

IDR

GPIO port input data register

Offset: 0x10, reset: 0x00000000, access: read-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IDR15 r	IDR14 r	IDR13 r	IDR12 r	IDR11 r	IDR10 r	IDR9 r	IDR8 r	IDR7 r	IDR6 r	IDR5 r	IDR4 r	IDR3 r	IDR2 r	IDR1 r	IDR0 r

Toggle Fields.

IDR0

Bit 0: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR1

Bit 1: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR2

Bit 2: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR3

Bit 3: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR4

Bit 4: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR5

Bit 5: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR6

Bit 6: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR7

Bit 7: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR8

Bit 8: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR9

Bit 9: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR10

Bit 10: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR11

Bit 11: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR12

Bit 12: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR13

Bit 13: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR14

Bit 14: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

IDR15

Bit 15: Port input data (y = 0..15).

Allowed values:
1: High: Input is logic high
0: Low: Input is logic low

ODR

GPIO port output data register

Offset: 0x14, reset: 0x00000000, access: read-write

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ODR15 rw	ODR14 rw	ODR13 rw	ODR12 rw	ODR11 rw	ODR10 rw	ODR9 rw	ODR8 rw	ODR7 rw	ODR6 rw	ODR5 rw	ODR4 rw	ODR3 rw	ODR2 rw	ODR1 rw	ODR0 rw

Toggle Fields.

ODR0

Bit 0: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR1

Bit 1: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR2

Bit 2: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR3

Bit 3: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR4

Bit 4: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR5

Bit 5: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR6

Bit 6: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR7

Bit 7: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR8

Bit 8: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR9

Bit 9: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR10

Bit 10: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR11

Bit 11: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR12

Bit 12: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR13

Bit 13: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR14

Bit 14: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

ODR15

Bit 15: Port output data (y = 0..15).

Allowed values:
1: High: Set output to logic high
0: Low: Set output to logic low

BSRR

GPIO port bit set/reset register

Offset: 0x18, reset: 0x00000000, access: write-only

32/32 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BS15 w	BS14 w	BS13 w	BS12 w	BS11 w	BS10 w	BS9 w	BS8 w	BS7 w	BS6 w	BS5 w	BS4 w	BS3 w	BS2 w	BS1 w	BS0 w

Toggle Fields.

BS0

Bit 0: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS1

Bit 1: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS2

Bit 2: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS3

Bit 3: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS4

Bit 4: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS5

Bit 5: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS6

Bit 6: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS7

Bit 7: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS8

Bit 8: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS9

Bit 9: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS10

Bit 10: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS11

Bit 11: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS12

Bit 12: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS13

Bit 13: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS14

Bit 14: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BS15

Bit 15: Port x set bit y (y= 0..15).

Allowed values:
1: Set: Sets the corresponding ODRx bit

BR0

Bit 16: Port x set bit y (y= 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR1

Bit 17: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR2

Bit 18: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR3

Bit 19: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR4

Bit 20: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR5

Bit 21: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR6

Bit 22: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR7

Bit 23: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR8

Bit 24: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR9

Bit 25: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR10

Bit 26: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR11

Bit 27: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR12

Bit 28: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR13

Bit 29: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR14

Bit 30: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

BR15

Bit 31: Port x reset bit y (y = 0..15).

Allowed values:
1: Reset: Resets the corresponding ODRx bit

LCKR

GPIO port configuration lock register

Offset: 0x1C, reset: 0x00000000, access: read-write

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															LCKK rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
LCK15 rw	LCK14 rw	LCK13 rw	LCK12 rw	LCK11 rw	LCK10 rw	LCK9 rw	LCK8 rw	LCK7 rw	LCK6 rw	LCK5 rw	LCK4 rw	LCK3 rw	LCK2 rw	LCK1 rw	LCK0 rw

Toggle Fields.

LCK0

Bit 0: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK1

Bit 1: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK2

Bit 2: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK3

Bit 3: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK4

Bit 4: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK5

Bit 5: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK6

Bit 6: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK7

Bit 7: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK8

Bit 8: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK9

Bit 9: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK10

Bit 10: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK11

Bit 11: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK12

Bit 12: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK13

Bit 13: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK14

Bit 14: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCK15

Bit 15: Port x lock bit y (y= 0..15).

Allowed values:
0: Unlocked: Port configuration not locked
1: Locked: Port configuration locked

LCKK

Bit 16: Port x lock bit y.

Allowed values:
0: NotActive: Port configuration lock key not active
1: Active: Port configuration lock key active

AFRL

GPIO alternate function low register

Offset: 0x20, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRL7 rw				AFRL6 rw				AFRL5 rw				AFRL4 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRL3 rw				AFRL2 rw				AFRL1 rw				AFRL0 rw

Toggle Fields.

AFRL0

Bits 0-3: Alternate function selection for port x bit y (y = 0..7).

AFRL1

Bits 4-7: Alternate function selection for port x bit y (y = 0..7).

AFRL2

Bits 8-11: Alternate function selection for port x bit y (y = 0..7).

AFRL3

Bits 12-15: Alternate function selection for port x bit y (y = 0..7).

AFRL4

Bits 16-19: Alternate function selection for port x bit y (y = 0..7).

AFRL5

Bits 20-23: Alternate function selection for port x bit y (y = 0..7).

AFRL6

Bits 24-27: Alternate function selection for port x bit y (y = 0..7).

AFRL7

Bits 28-31: Alternate function selection for port x bit y (y = 0..7).

AFRH

GPIO alternate function high register

Offset: 0x24, reset: 0x00000000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
AFRH15 rw				AFRH14 rw				AFRH13 rw				AFRH12 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
AFRH11 rw				AFRH10 rw				AFRH9 rw				AFRH8 rw

Toggle Fields.

AFRH8

Bits 0-3: Alternate function selection for port x bit y (y = 8..15).

AFRH9

Bits 4-7: Alternate function selection for port x bit y (y = 8..15).

AFRH10

Bits 8-11: Alternate function selection for port x bit y (y = 8..15).

AFRH11

Bits 12-15: Alternate function selection for port x bit y (y = 8..15).

AFRH12

Bits 16-19: Alternate function selection for port x bit y (y = 8..15).

AFRH13

Bits 20-23: Alternate function selection for port x bit y (y = 8..15).

AFRH14

Bits 24-27: Alternate function selection for port x bit y (y = 8..15).

AFRH15

Bits 28-31: Alternate function selection for port x bit y (y = 8..15).

BRR

Port bit reset register

Offset: 0x28, reset: 0x00000000, access: write-only

16/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BR15 w	BR14 w	BR13 w	BR12 w	BR11 w	BR10 w	BR9 w	BR8 w	BR7 w	BR6 w	BR5 w	BR4 w	BR3 w	BR2 w	BR1 w	BR0 w

Toggle Fields.

BR0

Bit 0: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR1

Bit 1: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR2

Bit 2: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR3

Bit 3: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR4

Bit 4: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR5

Bit 5: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR6

Bit 6: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR7

Bit 7: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR8

Bit 8: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR9

Bit 9: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR10

Bit 10: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR11

Bit 11: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR12

Bit 12: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR13

Bit 13: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR14

Bit 14: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

BR15

Bit 15: Port x Reset bit y.

Allowed values:
0: NoAction: No action on the corresponding ODx bit
1: Reset: Reset the ODx bit

I2C1

0x40005400: Inter-integrated circuit

76/77 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x00000000, access: Unspecified

20/21 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								PECEN rw	ALERTEN rw	SMBDEN rw	SMBHEN rw	GCEN rw	WUPEN rw	NOSTRETCH rw	SBC rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RXDMAEN rw	TXDMAEN rw	SWRST w	ANFOFF rw	DNF rw				ERRIE rw	TCIE rw	STOPIE rw	NACKIE rw	ADDRIE rw	RXIE rw	TXIE rw	PE rw

Toggle Fields.

PE

Bit 0: Peripheral enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

TXIE

Bit 1: TX Interrupt enable.

Allowed values:
0: Disabled: Transmit (TXIS) interrupt disabled
1: Enabled: Transmit (TXIS) interrupt enabled

RXIE

Bit 2: RX Interrupt enable.

Allowed values:
0: Disabled: Receive (RXNE) interrupt disabled
1: Enabled: Receive (RXNE) interrupt enabled

ADDRIE

Bit 3: Address match interrupt enable (slave only).

Allowed values:
0: Disabled: Address match (ADDR) interrupts disabled
1: Enabled: Address match (ADDR) interrupts enabled

NACKIE

Bit 4: Not acknowledge received interrupt enable.

Allowed values:
0: Disabled: Not acknowledge (NACKF) received interrupts disabled
1: Enabled: Not acknowledge (NACKF) received interrupts enabled

STOPIE

Bit 5: STOP detection Interrupt enable.

Allowed values:
0: Disabled: Stop detection (STOPF) interrupt disabled
1: Enabled: Stop detection (STOPF) interrupt enabled

TCIE

Bit 6: Transfer Complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

ERRIE

Bit 7: Error interrupts enable.

Allowed values:
0: Disabled: Error detection interrupts disabled
1: Enabled: Error detection interrupts enabled

DNF

Bits 8-11: Digital noise filter.

Allowed values:
0: NoFilter: Digital filter disabled
1: Filter1: Digital filter enabled and filtering capability up to 1 tI2CCLK
2: Filter2: Digital filter enabled and filtering capability up to 2 tI2CCLK
3: Filter3: Digital filter enabled and filtering capability up to 3 tI2CCLK
4: Filter4: Digital filter enabled and filtering capability up to 4 tI2CCLK
5: Filter5: Digital filter enabled and filtering capability up to 5 tI2CCLK
6: Filter6: Digital filter enabled and filtering capability up to 6 tI2CCLK
7: Filter7: Digital filter enabled and filtering capability up to 7 tI2CCLK
8: Filter8: Digital filter enabled and filtering capability up to 8 tI2CCLK
9: Filter9: Digital filter enabled and filtering capability up to 9 tI2CCLK
10: Filter10: Digital filter enabled and filtering capability up to 10 tI2CCLK
11: Filter11: Digital filter enabled and filtering capability up to 11 tI2CCLK
12: Filter12: Digital filter enabled and filtering capability up to 12 tI2CCLK
13: Filter13: Digital filter enabled and filtering capability up to 13 tI2CCLK
14: Filter14: Digital filter enabled and filtering capability up to 14 tI2CCLK
15: Filter15: Digital filter enabled and filtering capability up to 15 tI2CCLK

ANFOFF

Bit 12: Analog noise filter OFF.

Allowed values:
0: Enabled: Analog noise filter enabled
1: Disabled: Analog noise filter disabled

SWRST

Bit 13: Software reset.

TXDMAEN

Bit 14: DMA transmission requests enable.

Allowed values:
0: Disabled: DMA mode disabled for transmission
1: Enabled: DMA mode enabled for transmission

RXDMAEN

Bit 15: DMA reception requests enable.

Allowed values:
0: Disabled: DMA mode disabled for reception
1: Enabled: DMA mode enabled for reception

SBC

Bit 16: Slave byte control.

Allowed values:
0: Disabled: Slave byte control disabled
1: Enabled: Slave byte control enabled

NOSTRETCH

Bit 17: Clock stretching disable.

Allowed values:
0: Enabled: Clock stretching enabled
1: Disabled: Clock stretching disabled

WUPEN

Bit 18: Wakeup from STOP enable.

Allowed values:
0: Disabled: Wakeup from Stop mode disabled
1: Enabled: Wakeup from Stop mode enabled

GCEN

Bit 19: General call enable.

Allowed values:
0: Disabled: General call disabled. Address 0b00000000 is NACKed
1: Enabled: General call enabled. Address 0b00000000 is ACKed

SMBHEN

Bit 20: SMBus Host address enable.

Allowed values:
0: Disabled: Host address disabled. Address 0b0001000x is NACKed
1: Enabled: Host address enabled. Address 0b0001000x is ACKed

SMBDEN

Bit 21: SMBus Device Default address enable.

Allowed values:
0: Disabled: Device default address disabled. Address 0b1100001x is NACKed
1: Enabled: Device default address enabled. Address 0b1100001x is ACKed

ALERTEN

Bit 22: SMBUS alert enable.

Allowed values:
0: Disabled: In device mode (SMBHEN=Disabled) Releases SMBA pin high and Alert Response Address Header disabled (0001100x) followed by NACK. In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) not supported
1: Enabled: In device mode (SMBHEN=Disabled) Drives SMBA pin low and Alert Response Address Header enabled (0001100x) followed by ACK.In host mode (SMBHEN=Enabled) SMBus Alert pin (SMBA) supported

PECEN

Bit 23: PEC enable.

Allowed values:
0: Disabled: PEC calculation disabled
1: Enabled: PEC calculation enabled

CR2

Control register 2

Offset: 0x4, reset: 0x00000000, access: read-write

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					PECBYTE rw	AUTOEND rw	RELOAD rw	NBYTES rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NACK rw	STOP rw	START rw	HEAD10R rw	ADD10 rw	RD_WRN rw	SADD rw

Toggle Fields.

SADD

Bits 0-9: Slave address bit 9:8 (master mode).

Allowed values: 0-1023

RD_WRN

Bit 10: Transfer direction (master mode).

Allowed values:
0: Write: Master requests a write transfer
1: Read: Master requests a read transfer

ADD10

Bit 11: 10-bit addressing mode (master mode).

Allowed values:
0: Bit7: The master operates in 7-bit addressing mode
1: Bit10: The master operates in 10-bit addressing mode

HEAD10R

Bit 12: 10-bit address header only read direction (master receiver mode).

Allowed values:
0: Complete: The master sends the complete 10 bit slave address read sequence
1: Partial: The master only sends the 1st 7 bits of the 10 bit address, followed by Read direction

START

Bit 13: Start generation.

Allowed values:
0: NoStart: No Start generation
1: Start: Restart/Start generation

STOP

Bit 14: Stop generation (master mode).

Allowed values:
0: NoStop: No Stop generation
1: Stop: Stop generation after current byte transfer

NACK

Bit 15: NACK generation (slave mode).

Allowed values:
0: Ack: an ACK is sent after current received byte
1: Nack: a NACK is sent after current received byte

NBYTES

Bits 16-23: Number of bytes.

Allowed values: 0-255

RELOAD

Bit 24: NBYTES reload mode.

Allowed values:
0: Completed: The transfer is completed after the NBYTES data transfer (STOP or RESTART will follow)
1: NotCompeted: The transfer is not completed after the NBYTES data transfer (NBYTES will be reloaded)

AUTOEND

Bit 25: Automatic end mode (master mode).

Allowed values:
0: Software: Software end mode: TC flag is set when NBYTES data are transferred, stretching SCL low
1: Automatic: Automatic end mode: a STOP condition is automatically sent when NBYTES data are transferred

PECBYTE

Bit 26: Packet error checking byte.

Allowed values:
0: NoPec: No PEC transfer
1: Pec: PEC transmission/reception is requested

OAR1

Own address register 1

Offset: 0x8, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA1EN rw					OA1MODE rw	OA1 rw

Toggle Fields.

OA1

Bits 0-9: Interface address.

Allowed values: 0-1023

OA1MODE

Bit 10: Own Address 1 10-bit mode.

Allowed values:
0: Bit7: Own address 1 is a 7-bit address
1: Bit10: Own address 1 is a 10-bit address

OA1EN

Bit 15: Own Address 1 enable.

Allowed values:
0: Disabled: Own address 1 disabled. The received slave address OA1 is NACKed
1: Enabled: Own address 1 enabled. The received slave address OA1 is ACKed

OAR2

Own address register 2

Offset: 0xC, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA2EN rw					OA2MSK rw			OA2 rw

Toggle Fields.

OA2

Bits 1-7: Interface address.

Allowed values: 0-127

OA2MSK

Bits 8-10: Own Address 2 masks.

Allowed values:
0: NoMask: No mask
1: Mask1: OA2[1] is masked and don’t care. Only OA2[7:2] are compared
2: Mask2: OA2[2:1] are masked and don’t care. Only OA2[7:3] are compared
3: Mask3: OA2[3:1] are masked and don’t care. Only OA2[7:4] are compared
4: Mask4: OA2[4:1] are masked and don’t care. Only OA2[7:5] are compared
5: Mask5: OA2[5:1] are masked and don’t care. Only OA2[7:6] are compared
6: Mask6: OA2[6:1] are masked and don’t care. Only OA2[7] is compared.
7: Mask7: OA2[7:1] are masked and don’t care. No comparison is done, and all (except reserved) 7-bit received addresses are acknowledged

OA2EN

Bit 15: Own Address 2 enable.

Allowed values:
0: Disabled: Own address 2 disabled. The received slave address OA2 is NACKed
1: Enabled: Own address 2 enabled. The received slave address OA2 is ACKed

TIMINGR

Timing register

Offset: 0x10, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRESC rw								SCLDEL rw				SDADEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SCLH rw								SCLL rw

Offset: 0x14, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TEXTEN rw				TIMEOUTB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TIMOUTEN rw			TIDLE rw	TIMEOUTA rw

Toggle Fields.

TIMEOUTA

Bits 0-11: Bus timeout A.

Allowed values: 0-4095

TIDLE

Bit 12: Idle clock timeout detection.

Allowed values:
0: Disabled: TIMEOUTA is used to detect SCL low timeout
1: Enabled: TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition)

TIMOUTEN

Bit 15: Clock timeout enable.

Allowed values:
0: Disabled: SCL timeout detection is disabled
1: Enabled: SCL timeout detection is enabled

TIMEOUTB

Bits 16-27: Bus timeout B.

Allowed values: 0-4095

TEXTEN

Bit 31: Extended clock timeout enable.

Allowed values:
0: Disabled: Extended clock timeout detection is disabled
1: Enabled: Extended clock timeout detection is enabled

ISR

Interrupt and Status register

Offset: 0x18, reset: 0x00000001, access: Unspecified

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								ADDCODE r							DIR r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BUSY r		ALERT r	TIMEOUT r	PECERR r	OVR r	ARLO r	BERR r	TCR r	TC r	STOPF r	NACKF r	ADDR r	RXNE r	TXIS rw	TXE rw

Toggle Fields.

TXE

Bit 0: Transmit data register empty (transmitters).

Allowed values:
0: NotEmpty: TXDR register not empty
1: Empty: TXDR register empty

TXIS

Bit 1: Transmit interrupt status (transmitters).

Allowed values:
0: NotEmpty: The TXDR register is not empty
1: Empty: The TXDR register is empty and the data to be transmitted must be written in the TXDR register

RXNE

Bit 2: Receive data register not empty (receivers).

Allowed values:
0: Empty: The RXDR register is empty
1: NotEmpty: Received data is copied into the RXDR register, and is ready to be read

ADDR

Bit 3: Address matched (slave mode).

Allowed values:
0: NotMatch: Adress mismatched or not received
1: Match: Received slave address matched with one of the enabled slave addresses

NACKF

Bit 4: Not acknowledge received flag.

Allowed values:
0: NoNack: No NACK has been received
1: Nack: NACK has been received

STOPF

Bit 5: Stop detection flag.

Allowed values:
0: NoStop: No Stop condition detected
1: Stop: Stop condition detected

TC

Bit 6: Transfer Complete (master mode).

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

TCR

Bit 7: Transfer Complete Reload.

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

BERR

Bit 8: Bus error.

Allowed values:
0: NoError: No bus error
1: Error: Misplaced Start and Stop condition is detected

ARLO

Bit 9: Arbitration lost.

Allowed values:
0: NotLost: No arbitration lost
1: Lost: Arbitration lost

OVR

Bit 10: Overrun/Underrun (slave mode).

Allowed values:
0: NoOverrun: No overrun/underrun error occurs
1: Overrun: slave mode with NOSTRETCH=1, when an overrun/underrun error occurs

PECERR

Bit 11: PEC Error in reception.

Allowed values:
0: Match: Received PEC does match with PEC register
1: NoMatch: Received PEC does not match with PEC register

TIMEOUT

Bit 12: Timeout or t_low detection flag.

Allowed values:
0: NoTimeout: No timeout occured
1: Timeout: Timeout occured

ALERT

Bit 13: SMBus alert.

Allowed values:
0: NoAlert: SMBA alert is not detected
1: Alert: SMBA alert event is detected on SMBA pin

BUSY

Bit 15: Bus busy.

Allowed values:
0: NotBusy: No communication is in progress on the bus
1: Busy: A communication is in progress on the bus

DIR

Bit 16: Transfer direction (Slave mode).

Allowed values:
0: Write: Write transfer, slave enters receiver mode
1: Read: Read transfer, slave enters transmitter mode

ADDCODE

Bits 17-23: Address match code (Slave mode).

Allowed values: 0-127

ICR

Interrupt clear register

Offset: 0x1C, reset: 0x00000000, access: write-only

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		ALERTCF w	TIMOUTCF w	PECCF w	OVRCF w	ARLOCF w	BERRCF w			STOPCF w	NACKCF w	ADDRCF w

Toggle Fields.

ADDRCF

Bit 3: Address Matched flag clear.

Allowed values:
1: Clear: Clears the ADDR flag in ISR register

NACKCF

Bit 4: Not Acknowledge flag clear.

Allowed values:
1: Clear: Clears the NACK flag in ISR register

STOPCF

Bit 5: Stop detection flag clear.

Allowed values:
1: Clear: Clears the STOP flag in ISR register

BERRCF

Bit 8: Bus error flag clear.

Allowed values:
1: Clear: Clears the BERR flag in ISR register

ARLOCF

Bit 9: Arbitration lost flag clear.

Allowed values:
1: Clear: Clears the ARLO flag in ISR register

OVRCF

Bit 10: Overrun/Underrun flag clear.

Allowed values:
1: Clear: Clears the OVR flag in ISR register

PECCF

Bit 11: PEC Error flag clear.

Allowed values:
1: Clear: Clears the PEC flag in ISR register

TIMOUTCF

Bit 12: Timeout detection flag clear.

Allowed values:
1: Clear: Clears the TIMOUT flag in ISR register

ALERTCF

Bit 13: Alert flag clear.

Allowed values:
1: Clear: Clears the ALERT flag in ISR register

PECR

PEC register

Offset: 0x20, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								PEC r

Toggle Fields.

PEC

Bits 0-7: Packet error checking register.

Allowed values: 0-255

RXDR

Receive data register

Offset: 0x24, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								RXDATA r

Toggle Fields.

RXDATA

Bits 0-7: 8-bit receive data.

Allowed values: 0-255

TXDR

Transmit data register

Offset: 0x28, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TXDATA rw

Toggle Fields.

TXDATA

Bits 0-7: 8-bit transmit data.

Allowed values: 0-255

I2C2

0x40005800: Inter-integrated circuit

76/77 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x00000000, access: Unspecified

20/21 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								PECEN rw	ALERTEN rw	SMBDEN rw	SMBHEN rw	GCEN rw	WUPEN rw	NOSTRETCH rw	SBC rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RXDMAEN rw	TXDMAEN rw	SWRST w	ANFOFF rw	DNF rw				ERRIE rw	TCIE rw	STOPIE rw	NACKIE rw	ADDRIE rw	RXIE rw	TXIE rw	PE rw

Toggle Fields.

PE

Bit 0: Peripheral enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

TXIE

Bit 1: TX Interrupt enable.

Allowed values:
0: Disabled: Transmit (TXIS) interrupt disabled
1: Enabled: Transmit (TXIS) interrupt enabled

RXIE

Bit 2: RX Interrupt enable.

Allowed values:
0: Disabled: Receive (RXNE) interrupt disabled
1: Enabled: Receive (RXNE) interrupt enabled

ADDRIE

Bit 3: Address match interrupt enable (slave only).

Allowed values:
0: Disabled: Address match (ADDR) interrupts disabled
1: Enabled: Address match (ADDR) interrupts enabled

NACKIE

Bit 4: Not acknowledge received interrupt enable.

Allowed values:
0: Disabled: Not acknowledge (NACKF) received interrupts disabled
1: Enabled: Not acknowledge (NACKF) received interrupts enabled

STOPIE

Bit 5: STOP detection Interrupt enable.

Allowed values:
0: Disabled: Stop detection (STOPF) interrupt disabled
1: Enabled: Stop detection (STOPF) interrupt enabled

TCIE

Bit 6: Transfer Complete interrupt enable.

Allowed values:
0: Disabled: Transfer Complete interrupt disabled
1: Enabled: Transfer Complete interrupt enabled

ERRIE

Bit 7: Error interrupts enable.

Allowed values:
0: Disabled: Error detection interrupts disabled
1: Enabled: Error detection interrupts enabled

DNF

Bits 8-11: Digital noise filter.

ANFOFF

Bit 12: Analog noise filter OFF.

Allowed values:
0: Enabled: Analog noise filter enabled
1: Disabled: Analog noise filter disabled

SWRST

Bit 13: Software reset.

TXDMAEN

Bit 14: DMA transmission requests enable.

Allowed values:
0: Disabled: DMA mode disabled for transmission
1: Enabled: DMA mode enabled for transmission

RXDMAEN

Bit 15: DMA reception requests enable.

Allowed values:
0: Disabled: DMA mode disabled for reception
1: Enabled: DMA mode enabled for reception

SBC

Bit 16: Slave byte control.

Allowed values:
0: Disabled: Slave byte control disabled
1: Enabled: Slave byte control enabled

NOSTRETCH

Bit 17: Clock stretching disable.

Allowed values:
0: Enabled: Clock stretching enabled
1: Disabled: Clock stretching disabled

WUPEN

Bit 18: Wakeup from STOP enable.

Allowed values:
0: Disabled: Wakeup from Stop mode disabled
1: Enabled: Wakeup from Stop mode enabled

GCEN

Bit 19: General call enable.

Allowed values:
0: Disabled: General call disabled. Address 0b00000000 is NACKed
1: Enabled: General call enabled. Address 0b00000000 is ACKed

SMBHEN

Bit 20: SMBus Host address enable.

Allowed values:
0: Disabled: Host address disabled. Address 0b0001000x is NACKed
1: Enabled: Host address enabled. Address 0b0001000x is ACKed

SMBDEN

Bit 21: SMBus Device Default address enable.

Allowed values:
0: Disabled: Device default address disabled. Address 0b1100001x is NACKed
1: Enabled: Device default address enabled. Address 0b1100001x is ACKed

ALERTEN

Bit 22: SMBUS alert enable.

PECEN

Bit 23: PEC enable.

Allowed values:
0: Disabled: PEC calculation disabled
1: Enabled: PEC calculation enabled

CR2

Control register 2

Offset: 0x4, reset: 0x00000000, access: read-write

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
					PECBYTE rw	AUTOEND rw	RELOAD rw	NBYTES rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
NACK rw	STOP rw	START rw	HEAD10R rw	ADD10 rw	RD_WRN rw	SADD rw

Toggle Fields.

SADD

Bits 0-9: Slave address bit 9:8 (master mode).

Allowed values: 0-1023

RD_WRN

Bit 10: Transfer direction (master mode).

Allowed values:
0: Write: Master requests a write transfer
1: Read: Master requests a read transfer

ADD10

Bit 11: 10-bit addressing mode (master mode).

Allowed values:
0: Bit7: The master operates in 7-bit addressing mode
1: Bit10: The master operates in 10-bit addressing mode

HEAD10R

Bit 12: 10-bit address header only read direction (master receiver mode).

START

Bit 13: Start generation.

Allowed values:
0: NoStart: No Start generation
1: Start: Restart/Start generation

STOP

Bit 14: Stop generation (master mode).

Allowed values:
0: NoStop: No Stop generation
1: Stop: Stop generation after current byte transfer

NACK

Bit 15: NACK generation (slave mode).

Allowed values:
0: Ack: an ACK is sent after current received byte
1: Nack: a NACK is sent after current received byte

NBYTES

Bits 16-23: Number of bytes.

Allowed values: 0-255

RELOAD

Bit 24: NBYTES reload mode.

AUTOEND

Bit 25: Automatic end mode (master mode).

PECBYTE

Bit 26: Packet error checking byte.

Allowed values:
0: NoPec: No PEC transfer
1: Pec: PEC transmission/reception is requested

OAR1

Own address register 1

Offset: 0x8, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA1EN rw					OA1MODE rw	OA1 rw

Toggle Fields.

OA1

Bits 0-9: Interface address.

Allowed values: 0-1023

OA1MODE

Bit 10: Own Address 1 10-bit mode.

Allowed values:
0: Bit7: Own address 1 is a 7-bit address
1: Bit10: Own address 1 is a 10-bit address

OA1EN

Bit 15: Own Address 1 enable.

Allowed values:
0: Disabled: Own address 1 disabled. The received slave address OA1 is NACKed
1: Enabled: Own address 1 enabled. The received slave address OA1 is ACKed

OAR2

Own address register 2

Offset: 0xC, reset: 0x00000000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OA2EN rw					OA2MSK rw			OA2 rw

Toggle Fields.

OA2

Bits 1-7: Interface address.

Allowed values: 0-127

OA2MSK

Bits 8-10: Own Address 2 masks.

OA2EN

Bit 15: Own Address 2 enable.

Allowed values:
0: Disabled: Own address 2 disabled. The received slave address OA2 is NACKed
1: Enabled: Own address 2 enabled. The received slave address OA2 is ACKed

TIMINGR

Timing register

Offset: 0x10, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRESC rw								SCLDEL rw				SDADEL rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SCLH rw								SCLL rw

Offset: 0x14, reset: 0x00000000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
TEXTEN rw				TIMEOUTB rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TIMOUTEN rw			TIDLE rw	TIMEOUTA rw

Toggle Fields.

TIMEOUTA

Bits 0-11: Bus timeout A.

Allowed values: 0-4095

TIDLE

Bit 12: Idle clock timeout detection.

Allowed values:
0: Disabled: TIMEOUTA is used to detect SCL low timeout
1: Enabled: TIMEOUTA is used to detect both SCL and SDA high timeout (bus idle condition)

TIMOUTEN

Bit 15: Clock timeout enable.

Allowed values:
0: Disabled: SCL timeout detection is disabled
1: Enabled: SCL timeout detection is enabled

TIMEOUTB

Bits 16-27: Bus timeout B.

Allowed values: 0-4095

TEXTEN

Bit 31: Extended clock timeout enable.

Allowed values:
0: Disabled: Extended clock timeout detection is disabled
1: Enabled: Extended clock timeout detection is enabled

ISR

Interrupt and Status register

Offset: 0x18, reset: 0x00000001, access: Unspecified

17/17 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								ADDCODE r							DIR r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BUSY r		ALERT r	TIMEOUT r	PECERR r	OVR r	ARLO r	BERR r	TCR r	TC r	STOPF r	NACKF r	ADDR r	RXNE r	TXIS rw	TXE rw

Toggle Fields.

TXE

Bit 0: Transmit data register empty (transmitters).

Allowed values:
0: NotEmpty: TXDR register not empty
1: Empty: TXDR register empty

TXIS

Bit 1: Transmit interrupt status (transmitters).

Allowed values:
0: NotEmpty: The TXDR register is not empty
1: Empty: The TXDR register is empty and the data to be transmitted must be written in the TXDR register

RXNE

Bit 2: Receive data register not empty (receivers).

Allowed values:
0: Empty: The RXDR register is empty
1: NotEmpty: Received data is copied into the RXDR register, and is ready to be read

ADDR

Bit 3: Address matched (slave mode).

Allowed values:
0: NotMatch: Adress mismatched or not received
1: Match: Received slave address matched with one of the enabled slave addresses

NACKF

Bit 4: Not acknowledge received flag.

Allowed values:
0: NoNack: No NACK has been received
1: Nack: NACK has been received

STOPF

Bit 5: Stop detection flag.

Allowed values:
0: NoStop: No Stop condition detected
1: Stop: Stop condition detected

TC

Bit 6: Transfer Complete (master mode).

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

TCR

Bit 7: Transfer Complete Reload.

Allowed values:
0: NotComplete: Transfer is not complete
1: Complete: NBYTES has been transfered

BERR

Bit 8: Bus error.

Allowed values:
0: NoError: No bus error
1: Error: Misplaced Start and Stop condition is detected

ARLO

Bit 9: Arbitration lost.

Allowed values:
0: NotLost: No arbitration lost
1: Lost: Arbitration lost

OVR

Bit 10: Overrun/Underrun (slave mode).

Allowed values:
0: NoOverrun: No overrun/underrun error occurs
1: Overrun: slave mode with NOSTRETCH=1, when an overrun/underrun error occurs

PECERR

Bit 11: PEC Error in reception.

Allowed values:
0: Match: Received PEC does match with PEC register
1: NoMatch: Received PEC does not match with PEC register

TIMEOUT

Bit 12: Timeout or t_low detection flag.

Allowed values:
0: NoTimeout: No timeout occured
1: Timeout: Timeout occured

ALERT

Bit 13: SMBus alert.

Allowed values:
0: NoAlert: SMBA alert is not detected
1: Alert: SMBA alert event is detected on SMBA pin

BUSY

Bit 15: Bus busy.

Allowed values:
0: NotBusy: No communication is in progress on the bus
1: Busy: A communication is in progress on the bus

DIR

Bit 16: Transfer direction (Slave mode).

Allowed values:
0: Write: Write transfer, slave enters receiver mode
1: Read: Read transfer, slave enters transmitter mode

ADDCODE

Bits 17-23: Address match code (Slave mode).

Allowed values: 0-127

ICR

Interrupt clear register

Offset: 0x1C, reset: 0x00000000, access: write-only

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		ALERTCF w	TIMOUTCF w	PECCF w	OVRCF w	ARLOCF w	BERRCF w			STOPCF w	NACKCF w	ADDRCF w

Toggle Fields.

ADDRCF

Bit 3: Address Matched flag clear.

Allowed values:
1: Clear: Clears the ADDR flag in ISR register

NACKCF

Bit 4: Not Acknowledge flag clear.

Allowed values:
1: Clear: Clears the NACK flag in ISR register

STOPCF

Bit 5: Stop detection flag clear.

Allowed values:
1: Clear: Clears the STOP flag in ISR register

BERRCF

Bit 8: Bus error flag clear.

Allowed values:
1: Clear: Clears the BERR flag in ISR register

ARLOCF

Bit 9: Arbitration lost flag clear.

Allowed values:
1: Clear: Clears the ARLO flag in ISR register

OVRCF

Bit 10: Overrun/Underrun flag clear.

Allowed values:
1: Clear: Clears the OVR flag in ISR register

PECCF

Bit 11: PEC Error flag clear.

Allowed values:
1: Clear: Clears the PEC flag in ISR register

TIMOUTCF

Bit 12: Timeout detection flag clear.

Allowed values:
1: Clear: Clears the TIMOUT flag in ISR register

ALERTCF

Bit 13: Alert flag clear.

Allowed values:
1: Clear: Clears the ALERT flag in ISR register

PECR

PEC register

Offset: 0x20, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								PEC r

Toggle Fields.

PEC

Bits 0-7: Packet error checking register.

Allowed values: 0-255

RXDR

Receive data register

Offset: 0x24, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								RXDATA r

Toggle Fields.

RXDATA

Bits 0-7: 8-bit receive data.

Allowed values: 0-255

TXDR

Transmit data register

Offset: 0x28, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TXDATA rw

Toggle Fields.

TXDATA

Bits 0-7: 8-bit transmit data.

Allowed values: 0-255

IWDG

0x40003000: Independent watchdog

7/7 fields covered. Toggle Registers.

KR

Key register

Offset: 0x0, reset: 0x00000000, access: write-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
KEY w

Toggle Fields.

KEY

Bits 0-15: Key value.

Allowed values:
21845: Enable: Enable access to PR, RLR and WINR registers (0x5555)
43690: Reset: Reset the watchdog value (0xAAAA)
52428: Start: Start the watchdog (0xCCCC)

PR

Prescaler register

Offset: 0x4, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													PR rw

Toggle Fields.

PR

Bits 0-2: Prescaler divider.

Allowed values:
0: DivideBy4: Divider /4
1: DivideBy8: Divider /8
2: DivideBy16: Divider /16
3: DivideBy32: Divider /32
4: DivideBy64: Divider /64
5: DivideBy128: Divider /128
6: DivideBy256: Divider /256
7: DivideBy256bis: Divider /256

RLR

Reload register

Offset: 0x8, reset: 0x00000FFF, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				RL rw

Toggle Fields.

RL

Bits 0-11: Watchdog counter reload value.

Allowed values: 0-4095

SR

Status register

Offset: 0xC, reset: 0x00000000, access: read-only

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													WVU r	RVU r	PVU r

Toggle Fields.

PVU

Bit 0: Watchdog prescaler value update.

RVU

Bit 1: Watchdog counter reload value update.

WVU

Bit 2: Watchdog counter window value update.

WINR

Window register

Offset: 0x10, reset: 0x00000FFF, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				WIN rw

Toggle Fields.

WIN

Bits 0-11: Watchdog counter window value.

Allowed values: 0-4095

NVIC

0xE000E100: Nested Vectored Interrupt Controller

0/36 fields covered. Toggle Registers.

ISER

Interrupt Set Enable Register

Offset: 0x0, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SETENA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SETENA rw

Toggle Fields.

SETENA

Bits 0-31: SETENA.

ICER

Interrupt Clear Enable Register

Offset: 0x80, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CLRENA rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CLRENA rw

Toggle Fields.

CLRENA

Bits 0-31: CLRENA.

ISPR

Interrupt Set-Pending Register

Offset: 0x100, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
SETPEND rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SETPEND rw

Toggle Fields.

SETPEND

Bits 0-31: SETPEND.

ICPR

Interrupt Clear-Pending Register

Offset: 0x180, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CLRPEND rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CLRPEND rw

Toggle Fields.

CLRPEND

Bits 0-31: CLRPEND.

IPR0

Interrupt Priority Register 0

Offset: 0x300, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_03 rw								PRI_02 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PRI_01 rw								PRI_00 rw

Toggle Fields.

PRI_00

Bits 6-7: PRI_00.

PRI_01

Bits 14-15: PRI_01.

PRI_02

Bits 22-23: PRI_02.

PRI_03

Bits 30-31: PRI_03.

IPR1

Interrupt Priority Register 1

Offset: 0x304, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_43 rw								PRI_42 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PRI_41 rw								PRI_40 rw

Toggle Fields.

PRI_40

Bits 6-7: PRI_40.

PRI_41

Bits 14-15: PRI_41.

PRI_42

Bits 22-23: PRI_42.

PRI_43

Bits 30-31: PRI_43.

IPR2

Interrupt Priority Register 2

Offset: 0x308, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_83 rw								PRI_82 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PRI_81 rw								PRI_80 rw

Toggle Fields.

PRI_80

Bits 6-7: PRI_80.

PRI_81

Bits 14-15: PRI_81.

PRI_82

Bits 22-23: PRI_82.

PRI_83

Bits 30-31: PRI_83.

IPR3

Interrupt Priority Register 3

Offset: 0x30C, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_123 rw								PRI_122 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PRI_121 rw								PRI_120 rw

Toggle Fields.

PRI_120

Bits 6-7: PRI_120.

PRI_121

Bits 14-15: PRI_121.

PRI_122

Bits 22-23: PRI_122.

PRI_123

Bits 30-31: PRI_123.

IPR4

Interrupt Priority Register 4

Offset: 0x310, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_163 rw								PRI_162 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PRI_161 rw								PRI_160 rw

Toggle Fields.

PRI_160

Bits 6-7: PRI_160.

PRI_161

Bits 14-15: PRI_161.

PRI_162

Bits 22-23: PRI_162.

PRI_163

Bits 30-31: PRI_163.

IPR5

Interrupt Priority Register 5

Offset: 0x314, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_203 rw								PRI_202 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PRI_201 rw								PRI_200 rw

Toggle Fields.

PRI_200

Bits 6-7: PRI_200.

PRI_201

Bits 14-15: PRI_201.

PRI_202

Bits 22-23: PRI_202.

PRI_203

Bits 30-31: PRI_203.

IPR6

Interrupt Priority Register 6

Offset: 0x318, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_243 rw								PRI_242 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PRI_241 rw								PRI_240 rw

Toggle Fields.

PRI_240

Bits 6-7: PRI_240.

PRI_241

Bits 14-15: PRI_241.

PRI_242

Bits 22-23: PRI_242.

PRI_243

Bits 30-31: PRI_243.

IPR7

Interrupt Priority Register 7

Offset: 0x31C, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_283 rw								PRI_282 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PRI_281 rw								PRI_280 rw

Toggle Fields.

PRI_280

Bits 6-7: PRI_280.

PRI_281

Bits 14-15: PRI_281.

PRI_282

Bits 22-23: PRI_282.

PRI_283

Bits 30-31: PRI_283.

PWR

0x40007000: Power control

5/19 fields covered. Toggle Registers.

CR

power control register

Offset: 0x0, reset: 0x00000000, access: read-write

1/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							DBP rw	PLS rw			PVDE rw	CSBF rw	CWUF rw	PDDS rw	LPDS rw

Toggle Fields.

LPDS

Bit 0: Low-power deep sleep.

PDDS

Bit 1: Power down deepsleep.

Allowed values:
0: STOP_MODE: Enter Stop mode when the CPU enters deepsleep
1: STANDBY_MODE: Enter Standby mode when the CPU enters deepsleep

CWUF

Bit 2: Clear wakeup flag.

CSBF

Bit 3: Clear standby flag.

PVDE

Bit 4: Power voltage detector enable.

PLS

Bits 5-7: PVD level selection.

DBP

Bit 8: Disable backup domain write protection.

CSR

power control/status register

Offset: 0x4, reset: 0x00000000, access: Unspecified

4/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EWUP8 rw	EWUP7 rw	EWUP6 rw	EWUP5 rw	EWUP4 rw	EWUP3 rw	EWUP2 rw	EWUP1 rw					VREFINTRDY r	PVDO r	SBF r	WUF r

Toggle Fields.

WUF

Bit 0: Wakeup flag.

SBF

Bit 1: Standby flag.

PVDO

Bit 2: PVD output.

VREFINTRDY

Bit 3: VREFINT reference voltage ready.

EWUP1

Bit 8: Enable WKUP pin 1.

EWUP2

Bit 9: Enable WKUP pin 2.

EWUP3

Bit 10: Enable WKUP pin 3.

EWUP4

Bit 11: Enable WKUP pin 4.

EWUP5

Bit 12: Enable WKUP pin 5.

EWUP6

Bit 13: Enable WKUP pin 6.

EWUP7

Bit 14: Enable WKUP pin 7.

EWUP8

Bit 15: Enable WKUP pin 8.

RCC

0x40021000: Reset and clock control

153/155 fields covered. Toggle Registers.

CR

Clock control register

Offset: 0x0, reset: 0x00000083, access: Unspecified

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
						PLLRDY r	PLLON rw					CSSON rw	HSEBYP rw	HSERDY r	HSEON rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
HSICAL r								HSITRIM rw						HSIRDY r	HSION rw

Toggle Fields.

HSION

Bit 0: Internal High Speed clock enable.

Allowed values:
0: Off: Clock Off
1: On: Clock On

HSIRDY

Bit 1: Internal High Speed clock ready flag.

Allowed values:
0: NotReady: Clock not ready
1: Ready: Clock ready

HSITRIM

Bits 3-7: Internal High Speed clock trimming.

Allowed values: 0-31

HSICAL

Bits 8-15: Internal High Speed clock Calibration.

Allowed values: 0-255

HSEON

Bit 16: External High Speed clock enable.

Allowed values:
0: Off: Clock Off
1: On: Clock On

HSERDY

Bit 17: External High Speed clock ready flag.

Allowed values:
0: NotReady: Clock not ready
1: Ready: Clock ready

HSEBYP

Bit 18: External High Speed clock Bypass.

Allowed values:
0: NotBypassed: HSE crystal oscillator not bypassed
1: Bypassed: HSE crystal oscillator bypassed with external clock

CSSON

Bit 19: Clock Security System enable.

Allowed values:
0: Off: Clock security system disabled (clock detector OFF)
1: On: Clock security system enable (clock detector ON if the HSE is ready, OFF if not)

PLLON

Bit 24: PLL enable.

Allowed values:
0: Off: Clock Off
1: On: Clock On

PLLRDY

Bit 25: PLL clock ready flag.

Allowed values:
0: NotReady: Clock not ready
1: Ready: Clock ready

CFGR

Clock configuration register (RCC_CFGR)

Offset: 0x4, reset: 0x00000000, access: Unspecified

10/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PLLNODIV rw	MCOPRE rw				MCO rw					PLLMUL rw				PLLXTPRE rw	PLLSRC rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PLLSRC rw	ADCPRE rw				PPRE rw			HPRE rw				SWS r		SW rw

Toggle Fields.

SW

Bits 0-1: System clock Switch.

Allowed values:
3: HSI48: HSI48 selected as system clock (when available)
0: HSI: HSI selected as system clock
1: HSE: HSE selected as system clock
2: PLL: PLL selected as system clock

SWS

Bits 2-3: System Clock Switch Status.

Allowed values:
3: HSI48: HSI48 used as system clock (when avaiable)
0: HSI: HSE oscillator used as system clock
1: HSE: HSI oscillator used as system clock
2: PLL: PLL used as system clock

HPRE

Bits 4-7: AHB prescaler.

Allowed values:
0: Div1: SYSCLK not divided
8: Div2: SYSCLK divided by 2
9: Div4: SYSCLK divided by 4
10: Div8: SYSCLK divided by 8
11: Div16: SYSCLK divided by 16
12: Div64: SYSCLK divided by 64
13: Div128: SYSCLK divided by 128
14: Div256: SYSCLK divided by 256
15: Div512: SYSCLK divided by 512

PPRE

Bits 8-10: APB Low speed prescaler (APB1).

Allowed values:
0: Div1: HCLK not divided
4: Div2: HCLK divided by 2
5: Div4: HCLK divided by 4
6: Div8: HCLK divided by 8
7: Div16: HCLK divided by 16

ADCPRE

Bit 14: APCPRE is deprecated. See ADC field in CFGR2 register..

PLLSRC

Bits 15-16: PLL input clock source.

Allowed values:
3: HSI48_Div_PREDIV: HSI48 divided by PREDIV selected as PLL input clock
0: HSI_Div2: HSI divided by 2 selected as PLL input clock
1: HSI_Div_PREDIV: HSI divided by PREDIV selected as PLL input clock
2: HSE_Div_PREDIV: HSE divided by PREDIV selected as PLL input clock

PLLXTPRE

Bit 17: HSE divider for PLL entry. Same bit as PREDIC[0] from CFGR2 register. Refer to it for its meaning.

Allowed values:
0: Div1: HSE clock not divided
1: Div2: HSE clock divided by 2

PLLMUL

Bits 18-21: PLL Multiplication Factor.

Allowed values:
0: Mul2: PLL input clock x2
1: Mul3: PLL input clock x3
2: Mul4: PLL input clock x4
3: Mul5: PLL input clock x5
4: Mul6: PLL input clock x6
5: Mul7: PLL input clock x7
6: Mul8: PLL input clock x8
7: Mul9: PLL input clock x9
8: Mul10: PLL input clock x10
9: Mul11: PLL input clock x11
10: Mul12: PLL input clock x12
11: Mul13: PLL input clock x13
12: Mul14: PLL input clock x14
13: Mul15: PLL input clock x15
14: Mul16: PLL input clock x16
15: Mul16x: PLL input clock x16

MCO

Bits 24-26: Microcontroller clock output.

Allowed values:
1: HSI14: Internal RC 14 MHz (HSI14) oscillator clock selected
8: HSI48: Internal RC 48 MHz (HSI48) oscillator clock selected
0: NoMCO: MCO output disabled, no clock on MCO
2: LSI: Internal low speed (LSI) oscillator clock selected
3: LSE: External low speed (LSE) oscillator clock selected
4: SYSCLK: System clock selected
5: HSI: Internal RC 8 MHz (HSI) oscillator clock selected
6: HSE: External 4-32 MHz (HSE) oscillator clock selected
7: PLL: PLL clock selected (divided by 1 or 2, depending en PLLNODIV)

MCOPRE

Bits 28-30: Microcontroller Clock Output Prescaler.

Allowed values:
0: Div1: MCO is divided by 1
1: Div2: MCO is divided by 2
2: Div4: MCO is divided by 4
3: Div8: MCO is divided by 8
4: Div16: MCO is divided by 16
5: Div32: MCO is divided by 32
6: Div64: MCO is divided by 64
7: Div128: MCO is divided by 128

PLLNODIV

Bit 31: PLL clock not divided for MCO.

Allowed values:
0: Div2: PLL is divided by 2 for MCO
1: Div1: PLL is not divided for MCO

CIR

Clock interrupt register (RCC_CIR)

Offset: 0x8, reset: 0x00000000, access: Unspecified

23/23 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								CSSC w	HSI48RDYC w	HSI14RDYC w	PLLRDYC w	HSERDYC w	HSIRDYC w	LSERDYC w	LSIRDYC w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	HSI48RDYIE rw	HSI14RDYIE rw	PLLRDYIE rw	HSERDYIE rw	HSIRDYIE rw	LSERDYIE rw	LSIRDYIE rw	CSSF r	HSI48RDYF r	HSI14RDYF r	PLLRDYF r	HSERDYF r	HSIRDYF r	LSERDYF r	LSIRDYF r

Toggle Fields.

LSIRDYF

Bit 0: LSI Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

LSERDYF

Bit 1: LSE Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

HSIRDYF

Bit 2: HSI Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

HSERDYF

Bit 3: HSE Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

PLLRDYF

Bit 4: PLL Ready Interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

HSI14RDYF

Bit 5: HSI14 ready interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

HSI48RDYF

Bit 6: HSI48 ready interrupt flag.

Allowed values:
0: NotInterrupted: No clock ready interrupt
1: Interrupted: Clock ready interrupt

CSSF

Bit 7: Clock Security System Interrupt flag.

Allowed values:
0: NotInterrupted: No clock security interrupt caused by HSE clock failure
1: Interrupted: Clock security interrupt caused by HSE clock failure

LSIRDYIE

Bit 8: LSI Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

LSERDYIE

Bit 9: LSE Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

HSIRDYIE

Bit 10: HSI Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

HSERDYIE

Bit 11: HSE Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

PLLRDYIE

Bit 12: PLL Ready Interrupt Enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

HSI14RDYIE

Bit 13: HSI14 ready interrupt enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

HSI48RDYIE

Bit 14: HSI48 ready interrupt enable.

Allowed values:
0: Disabled: Interrupt disabled
1: Enabled: Interrupt enabled

LSIRDYC

Bit 16: LSI Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

LSERDYC

Bit 17: LSE Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

HSIRDYC

Bit 18: HSI Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

HSERDYC

Bit 19: HSE Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

PLLRDYC

Bit 20: PLL Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

HSI14RDYC

Bit 21: HSI 14 MHz Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

HSI48RDYC

Bit 22: HSI48 Ready Interrupt Clear.

Allowed values:
1: Clear: Clear interrupt flag

CSSC

Bit 23: Clock security system interrupt clear.

Allowed values:
1: Clear: Clear CSSF flag

APB2RSTR

APB2 peripheral reset register (RCC_APB2RSTR)

Offset: 0xC, reset: 0x00000000, access: read-write

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									DBGMCURST rw				TIM17RST rw	TIM16RST rw	TIM15RST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	USART1RST rw		SPI1RST rw	TIM1RST rw		ADCRST rw				USART6RST rw					SYSCFGRST rw

Toggle Fields.

SYSCFGRST

Bit 0: SYSCFG and COMP reset.

Allowed values:
1: Reset: Reset the selected module

USART6RST

Bit 5: USART6 reset.

Allowed values:
1: Reset: Reset the selected module

ADCRST

Bit 9: ADC interface reset.

Allowed values:
1: Reset: Reset the selected module

TIM1RST

Bit 11: TIM1 timer reset.

Allowed values:
1: Reset: Reset the selected module

SPI1RST

Bit 12: SPI 1 reset.

Allowed values:
1: Reset: Reset the selected module

USART1RST

Bit 14: USART1 reset.

Allowed values:
1: Reset: Reset the selected module

TIM15RST

Bit 16: TIM15 timer reset.

Allowed values:
1: Reset: Reset the selected module

TIM16RST

Bit 17: TIM16 timer reset.

Allowed values:
1: Reset: Reset the selected module

TIM17RST

Bit 18: TIM17 timer reset.

Allowed values:
1: Reset: Reset the selected module

DBGMCURST

Bit 22: Debug MCU reset.

Allowed values:
1: Reset: Reset the selected module

APB1RSTR

APB1 peripheral reset register (RCC_APB1RSTR)

Offset: 0x10, reset: 0x00000000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	CECRST rw	DACRST rw	PWRRST rw	CRSRST rw		CANRST rw		USBRST rw	I2C2RST rw	I2C1RST rw	USART5RST rw	USART4RST rw	USART3RST rw	USART2RST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SPI2RST rw			WWDGRST rw			TIM14RST rw			TIM7RST rw	TIM6RST rw			TIM3RST rw	TIM2RST rw

Toggle Fields.

TIM2RST

Bit 0: Timer 2 reset.

Allowed values:
1: Reset: Reset the selected module

TIM3RST

Bit 1: Timer 3 reset.

Allowed values:
1: Reset: Reset the selected module

TIM6RST

Bit 4: Timer 6 reset.

Allowed values:
1: Reset: Reset the selected module

TIM7RST

Bit 5: TIM7 timer reset.

Allowed values:
1: Reset: Reset the selected module

TIM14RST

Bit 8: Timer 14 reset.

Allowed values:
1: Reset: Reset the selected module

WWDGRST

Bit 11: Window watchdog reset.

Allowed values:
1: Reset: Reset the selected module

SPI2RST

Bit 14: SPI2 reset.

Allowed values:
1: Reset: Reset the selected module

USART2RST

Bit 17: USART 2 reset.

Allowed values:
1: Reset: Reset the selected module

USART3RST

Bit 18: USART3 reset.

Allowed values:
1: Reset: Reset the selected module

USART4RST

Bit 19: USART4 reset.

Allowed values:
1: Reset: Reset the selected module

USART5RST

Bit 20: USART5 reset.

Allowed values:
1: Reset: Reset the selected module

I2C1RST

Bit 21: I2C1 reset.

Allowed values:
1: Reset: Reset the selected module

I2C2RST

Bit 22: I2C2 reset.

Allowed values:
1: Reset: Reset the selected module

USBRST

Bit 23: USB interface reset.

Allowed values:
1: Reset: Reset the selected module

CANRST

Bit 25: CAN interface reset.

Allowed values:
1: Reset: Reset the selected module

CRSRST

Bit 27: Clock Recovery System interface reset.

Allowed values:
1: Reset: Reset the selected module

PWRRST

Bit 28: Power interface reset.

Allowed values:
1: Reset: Reset the selected module

DACRST

Bit 29: DAC interface reset.

Allowed values:
1: Reset: Reset the selected module

CECRST

Bit 30: HDMI CEC reset.

Allowed values:
1: Reset: Reset the selected module

AHBENR

AHB Peripheral Clock enable register (RCC_AHBENR)

Offset: 0x14, reset: 0x00000014, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							TSCEN rw		IOPFEN rw	IOPEEN rw	IOPDEN rw	IOPCEN rw	IOPBEN rw	IOPAEN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									CRCEN rw		FLITFEN rw		SRAMEN rw		DMAEN rw

Toggle Fields.

DMAEN

Bit 0: DMA clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SRAMEN

Bit 2: SRAM interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

FLITFEN

Bit 4: FLITF clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

CRCEN

Bit 6: CRC clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPAEN

Bit 17: I/O port A clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPBEN

Bit 18: I/O port B clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPCEN

Bit 19: I/O port C clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPDEN

Bit 20: I/O port D clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPEEN

Bit 21: I/O port E clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

IOPFEN

Bit 22: I/O port F clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TSCEN

Bit 24: Touch sensing controller clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

APB2ENR

APB2 peripheral clock enable register (RCC_APB2ENR)

Offset: 0x18, reset: 0x00000000, access: read-write

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									DBGMCUEN rw				TIM17EN rw	TIM16EN rw	TIM15EN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	USART1EN rw		SPI1EN rw	TIM1EN rw		ADCEN rw				USART6EN rw					SYSCFGEN rw

Toggle Fields.

SYSCFGEN

Bit 0: SYSCFG clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART6EN

Bit 5: USART6 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

ADCEN

Bit 9: ADC 1 interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM1EN

Bit 11: TIM1 Timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SPI1EN

Bit 12: SPI 1 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART1EN

Bit 14: USART1 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM15EN

Bit 16: TIM15 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM16EN

Bit 17: TIM16 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM17EN

Bit 18: TIM17 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

DBGMCUEN

Bit 22: MCU debug module clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

APB1ENR

APB1 peripheral clock enable register (RCC_APB1ENR)

Offset: 0x1C, reset: 0x00000000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	CECEN rw	DACEN rw	PWREN rw	CRSEN rw		CANEN rw		USBEN rw	I2C2EN rw	I2C1EN rw	USART5EN rw	USART4EN rw	USART3EN rw	USART2EN rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SPI2EN rw			WWDGEN rw			TIM14EN rw			TIM7EN rw	TIM6EN rw			TIM3EN rw	TIM2EN rw

Toggle Fields.

TIM2EN

Bit 0: Timer 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM3EN

Bit 1: Timer 3 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM6EN

Bit 4: Timer 6 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM7EN

Bit 5: TIM7 timer clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

TIM14EN

Bit 8: Timer 14 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

WWDGEN

Bit 11: Window watchdog clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

SPI2EN

Bit 14: SPI 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART2EN

Bit 17: USART 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART3EN

Bit 18: USART3 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART4EN

Bit 19: USART4 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USART5EN

Bit 20: USART5 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

I2C1EN

Bit 21: I2C 1 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

I2C2EN

Bit 22: I2C 2 clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

USBEN

Bit 23: USB interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

CANEN

Bit 25: CAN interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

CRSEN

Bit 27: Clock Recovery System interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

PWREN

Bit 28: Power interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

DACEN

Bit 29: DAC interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

CECEN

Bit 30: HDMI CEC interface clock enable.

Allowed values:
0: Disabled: The selected clock is disabled
1: Enabled: The selected clock is enabled

BDCR

Backup domain control register (RCC_BDCR)

Offset: 0x20, reset: 0x00000000, access: Unspecified

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															BDRST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTCEN rw						RTCSEL rw					LSEDRV rw		LSEBYP rw	LSERDY r	LSEON rw

Toggle Fields.

LSEON

Bit 0: External Low Speed oscillator enable.

Allowed values:
0: Off: LSE oscillator Off
1: On: LSE oscillator On

LSERDY

Bit 1: External Low Speed oscillator ready.

Allowed values:
0: NotReady: LSE oscillator not ready
1: Ready: LSE oscillator ready

LSEBYP

Bit 2: External Low Speed oscillator bypass.

Allowed values:
0: NotBypassed: LSE crystal oscillator not bypassed
1: Bypassed: LSE crystal oscillator bypassed with external clock

LSEDRV

Bits 3-4: LSE oscillator drive capability.

Allowed values:
0: Low: Low drive capacity
1: MediumHigh: Medium-high drive capacity
2: MediumLow: Medium-low drive capacity
3: High: High drive capacity

RTCSEL

Bits 8-9: RTC clock source selection.

Allowed values:
0: NoClock: No clock
1: LSE: LSE oscillator clock used as RTC clock
2: LSI: LSI oscillator clock used as RTC clock
3: HSE: HSE oscillator clock divided by a prescaler used as RTC clock

RTCEN

Bit 15: RTC clock enable.

Allowed values:
0: Disabled: RTC clock disabled
1: Enabled: RTC clock enabled

BDRST

Bit 16: Backup domain software reset.

Allowed values:
0: Disabled: Reset not activated
1: Enabled: Reset the entire RTC domain

CSR

Control/status register (RCC_CSR)

Offset: 0x24, reset: 0x0C000000, access: Unspecified

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
LPWRRSTF rw	WWDGRSTF rw	IWDGRSTF rw	SFTRSTF rw	PORRSTF rw	PINRSTF rw	OBLRSTF rw	RMVF rw	V18PWRRSTF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														LSIRDY r	LSION rw

Toggle Fields.

LSION

Bit 0: Internal low speed oscillator enable.

Allowed values:
0: Off: LSI oscillator Off
1: On: LSI oscillator On

LSIRDY

Bit 1: Internal low speed oscillator ready.

Allowed values:
0: NotReady: LSI oscillator not ready
1: Ready: LSI oscillator ready

V18PWRRSTF

Bit 23: 1.8 V domain reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

RMVF

Bit 24: Remove reset flag.

Allowed values:
1: Clear: Clears the reset flag

OBLRSTF

Bit 25: Option byte loader reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

PINRSTF

Bit 26: PIN reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

PORRSTF

Bit 27: POR/PDR reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

SFTRSTF

Bit 28: Software reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

IWDGRSTF

Bit 29: Independent watchdog reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

WWDGRSTF

Bit 30: Window watchdog reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

LPWRRSTF

Bit 31: Low-power reset flag.

Allowed values:
0: NoReset: No reset has occured
1: Reset: A reset has occured

AHBRSTR

AHB peripheral reset register

Offset: 0x28, reset: 0x00000000, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
							TSCRST rw		IOPFRST rw	IOPERST rw	IOPDRST rw	IOPCRST rw	IOPBRST rw	IOPARST rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0

Toggle Fields.

IOPARST

Bit 17: I/O port A reset.

Allowed values:
1: Reset: Reset the selected module

IOPBRST

Bit 18: I/O port B reset.

Allowed values:
1: Reset: Reset the selected module

IOPCRST

Bit 19: I/O port C reset.

Allowed values:
1: Reset: Reset the selected module

IOPDRST

Bit 20: I/O port D reset.

Allowed values:
1: Reset: Reset the selected module

IOPERST

Bit 21: I/O port E reset.

Allowed values:
1: Reset: Reset the selected module

IOPFRST

Bit 22: I/O port F reset.

Allowed values:
1: Reset: Reset the selected module

TSCRST

Bit 24: Touch sensing controller reset.

Allowed values:
1: Reset: Reset the selected module

CFGR2

Clock configuration register 2

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												PREDIV rw

Toggle Fields.

PREDIV

Bits 0-3: PREDIV division factor.

Allowed values:
0: Div1: PREDIV input clock not divided
1: Div2: PREDIV input clock divided by 2
2: Div3: PREDIV input clock divided by 3
3: Div4: PREDIV input clock divided by 4
4: Div5: PREDIV input clock divided by 5
5: Div6: PREDIV input clock divided by 6
6: Div7: PREDIV input clock divided by 7
7: Div8: PREDIV input clock divided by 8
8: Div9: PREDIV input clock divided by 9
9: Div10: PREDIV input clock divided by 10
10: Div11: PREDIV input clock divided by 11
11: Div12: PREDIV input clock divided by 12
12: Div13: PREDIV input clock divided by 13
13: Div14: PREDIV input clock divided by 14
14: Div15: PREDIV input clock divided by 15
15: Div16: PREDIV input clock divided by 16

CFGR3

Clock configuration register 3

Offset: 0x30, reset: 0x00000000, access: read-write

6/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
												USART3SW rw		USART2SW rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							ADCSW rw	USBSW rw	CECSW rw		I2C1SW rw			USART1SW rw

Toggle Fields.

USART1SW

Bits 0-1: USART1 clock source selection.

Allowed values:
0: PCLK: PCLK selected as USART clock source
1: SYSCLK: SYSCLK selected as USART clock source
2: LSE: LSE selected as USART clock source
3: HSI: HSI selected as USART clock source

I2C1SW

Bit 4: I2C1 clock source selection.

Allowed values:
0: HSI: HSI clock selected as I2C clock source
1: SYSCLK: SYSCLK clock selected as I2C clock source

CECSW

Bit 6: HDMI CEC clock source selection.

Allowed values:
0: HSI_Div244: HSI clock divided by 244 selected as CEC clock source
1: LSE: LSE clock selected as CEC clock source

USBSW

Bit 7: USB clock source selection.

Allowed values:
0: HSI48: HSI48 selected as USB clock source
1: PLLCLK: PLL clock selected as USB clock source

ADCSW

Bit 8: ADCSW is deprecated. See ADC field in CFGR2 register..

USART2SW

Bits 16-17: USART2 clock source selection.

USART3SW

Bits 18-19: USART3 clock source.

CR2

Clock control register 2

Offset: 0x34, reset: 0x00000080, access: Unspecified

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
HSI48CAL r														HSI48RDY r	HSI48ON rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
HSI14CAL r								HSI14TRIM rw					HSI14DIS rw	HSI14RDY r	HSI14ON rw

Toggle Fields.

HSI14ON

Bit 0: HSI14 clock enable.

Allowed values:
0: Off: HSI14 oscillator off
1: On: HSI14 oscillator on

HSI14RDY

Bit 1: HR14 clock ready flag.

Allowed values:
0: NotReady: HSI14 oscillator not ready
1: Ready: HSI14 oscillator ready

HSI14DIS

Bit 2: HSI14 clock request from ADC disable.

Allowed values:
0: Allow: ADC can turn on the HSI14 oscillator
1: Disallow: ADC can not turn on the HSI14 oscillator

HSI14TRIM

Bits 3-7: HSI14 clock trimming.

Allowed values: 0-31

HSI14CAL

Bits 8-15: HSI14 clock calibration.

Allowed values: 0-255

HSI48ON

Bit 16: HSI48 clock enable.

Allowed values:
0: Off: HSI48 oscillator off
1: On: HSI48 oscillator on

HSI48RDY

Bit 17: HSI48 clock ready flag.

Allowed values:
0: NotReady: HSI48 oscillator ready
1: Ready: HSI48 oscillator ready

HSI48CAL

Bits 24-31: HSI48 factory clock calibration.

Allowed values: 0-255

RTC

0x40002800: Real-time clock

18/97 fields covered. Toggle Registers.

TR

time register

Offset: 0x0, reset: 0x00000000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									PM rw	HT rw		HU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MNT rw			MNU rw					ST rw			SU rw

Toggle Fields.

SU

Bits 0-3: Second units in BCD format.

ST

Bits 4-6: Second tens in BCD format.

MNU

Bits 8-11: Minute units in BCD format.

MNT

Bits 12-14: Minute tens in BCD format.

HU

Bits 16-19: Hour units in BCD format.

HT

Bits 20-21: Hour tens in BCD format.

PM

Bit 22: AM/PM notation.

DR

date register

Offset: 0x4, reset: 0x00002101, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								YT rw				YU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
WDU rw			MT rw	MU rw						DT rw		DU rw

Toggle Fields.

DU

Bits 0-3: Date units in BCD format.

DT

Bits 4-5: Date tens in BCD format.

MU

Bits 8-11: Month units in BCD format.

MT

Bit 12: Month tens in BCD format.

WDU

Bits 13-15: Week day units.

YU

Bits 16-19: Year units in BCD format.

YT

Bits 20-23: Year tens in BCD format.

CR

control register

Offset: 0x8, reset: 0x00000000, access: Unspecified

0/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								COE rw	OSEL rw		POL rw	COSEL rw	BKP rw	SUB1H w	ADD1H w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TSIE rw			ALRAIE rw	TSE rw			ALRAE rw		FMT rw	BYPSHAD rw	REFCKON rw	TSEDGE rw

Toggle Fields.

TSEDGE

Bit 3: Time-stamp event active edge.

REFCKON

Bit 4: RTC_REFIN reference clock detection enable (50 or 60 Hz).

BYPSHAD

Bit 5: Bypass the shadow registers.

FMT

Bit 6: Hour format.

ALRAE

Bit 8: Alarm A enable.

TSE

Bit 11: timestamp enable.

ALRAIE

Bit 12: Alarm A interrupt enable.

TSIE

Bit 15: Time-stamp interrupt enable.

ADD1H

Bit 16: Add 1 hour (summer time change).

SUB1H

Bit 17: Subtract 1 hour (winter time change).

BKP

Bit 18: Backup.

COSEL

Bit 19: Calibration output selection.

POL

Bit 20: Output polarity.

OSEL

Bits 21-22: Output selection.

COE

Bit 23: Calibration output enable.

ISR

initialization and status register

Offset: 0xC, reset: 0x00000007, access: Unspecified

4/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															RECALPF r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TAMP2F rw	TAMP1F rw	TSOVF rw	TSF rw			ALRAF rw	INIT rw	INITF r	RSF rw	INITS r	SHPF rw			ALRAWF r

Toggle Fields.

ALRAWF

Bit 0: Alarm A write flag.

SHPF

Bit 3: Shift operation pending.

INITS

Bit 4: Initialization status flag.

RSF

Bit 5: Registers synchronization flag.

INITF

Bit 6: Initialization flag.

INIT

Bit 7: Initialization mode.

ALRAF

Bit 8: Alarm A flag.

TSF

Bit 11: Time-stamp flag.

TSOVF

Bit 12: Time-stamp overflow flag.

TAMP1F

Bit 13: RTC_TAMP1 detection flag.

TAMP2F

Bit 14: RTC_TAMP2 detection flag.

RECALPF

Bit 16: Recalibration pending Flag.

PRER

prescaler register

Offset: 0x10, reset: 0x007F00FF, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									PREDIV_A rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	PREDIV_S rw

Toggle Fields.

PREDIV_S

Bits 0-14: Synchronous prescaler factor.

PREDIV_A

Bits 16-22: Asynchronous prescaler factor.

ALRMAR

alarm A register

Offset: 0x1C, reset: 0x00000000, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
MSK4 rw	WDSEL rw	DT rw		DU rw				MSK3 rw	PM rw	HT rw		HU rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MSK2 rw	MNT rw			MNU rw				MSK1 rw	ST rw			SU rw

Toggle Fields.

SU

Bits 0-3: Second units in BCD format..

ST

Bits 4-6: Second tens in BCD format..

MSK1

Bit 7: Alarm A seconds mask.

MNU

Bits 8-11: Minute units in BCD format..

MNT

Bits 12-14: Minute tens in BCD format..

MSK2

Bit 15: Alarm A minutes mask.

HU

Bits 16-19: Hour units in BCD format..

HT

Bits 20-21: Hour tens in BCD format..

PM

Bit 22: AM/PM notation.

MSK3

Bit 23: Alarm A hours mask.

DU

Bits 24-27: Date units or day in BCD format..

DT

Bits 28-29: Date tens in BCD format..

WDSEL

Bit 30: Week day selection.

MSK4

Bit 31: Alarm A date mask.

WPR

write protection register

Offset: 0x24, reset: 0x00000000, access: write-only

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								KEY w

Toggle Fields.

KEY

Bits 0-7: Write protection key.

SSR

sub second register

Offset: 0x28, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SS r

Toggle Fields.

SS

Bits 0-15: Sub second value.

SHIFTR

shift control register

Offset: 0x2C, reset: 0x00000000, access: write-only

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD1S w
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SUBFS w

Toggle Fields.

SUBFS

Bits 0-14: Subtract a fraction of a second.

ADD1S

Bit 31: Add one second.

TSTR

timestamp time register

Offset: 0x30, reset: 0x00000000, access: read-only

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									PM r	HT r		HU r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	MNT r			MNU r					ST r			SU r

Toggle Fields.

SU

Bits 0-3: Second units in BCD format..

ST

Bits 4-6: Second tens in BCD format..

MNU

Bits 8-11: Minute units in BCD format..

MNT

Bits 12-14: Minute tens in BCD format..

HU

Bits 16-19: Hour units in BCD format..

HT

Bits 20-21: Hour tens in BCD format..

PM

Bit 22: AM/PM notation.

TSDR

timestamp date register

Offset: 0x34, reset: 0x00000000, access: read-only

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
WDU r			MT r	MU r						DT r		DU r

Toggle Fields.

DU

Bits 0-3: Date units in BCD format.

DT

Bits 4-5: Date tens in BCD format.

MU

Bits 8-11: Month units in BCD format.

MT

Bit 12: Month tens in BCD format.

WDU

Bits 13-15: Week day units.

TSSSR

time-stamp sub second register

Offset: 0x38, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SS r

Toggle Fields.

SS

Bits 0-15: Sub second value.

CALR

calibration register

Offset: 0x3C, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CALP rw	CALW8 rw	CALW16 rw					CALM rw

Toggle Fields.

CALM

Bits 0-8: Calibration minus.

CALW16

Bit 13: Use a 16-second calibration cycle period.

CALW8

Bit 14: Use an 8-second calibration cycle period.

CALP

Bit 15: Increase frequency of RTC by 488.5 ppm.

TAFCR

tamper and alternate function configuration register

Offset: 0x40, reset: 0x00000000, access: read-write

0/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								PC15MODE rw	PC15VALUE rw	PC14MODE rw	PC14VALUE rw	PC13MODE rw	PC13VALUE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TAMP_PUDIS rw	TAMP_PRCH rw		TAMPFLT rw		TAMPFREQ rw			TAMPTS rw			TAMP2_TRG rw	TAMP2E rw	TAMPIE rw	TAMP1TRG rw	TAMP1E rw

Toggle Fields.

TAMP1E

Bit 0: RTC_TAMP1 input detection enable.

TAMP1TRG

Bit 1: Active level for RTC_TAMP1 input.

TAMPIE

Bit 2: Tamper interrupt enable.

TAMP2E

Bit 3: RTC_TAMP2 input detection enable.

TAMP2_TRG

Bit 4: Active level for RTC_TAMP2 input.

TAMPTS

Bit 7: Activate timestamp on tamper detection event.

TAMPFREQ

Bits 8-10: Tamper sampling frequency.

TAMPFLT

Bits 11-12: RTC_TAMPx filter count.

TAMP_PRCH

Bits 13-14: RTC_TAMPx precharge duration.

TAMP_PUDIS

Bit 15: RTC_TAMPx pull-up disable.

PC13VALUE

Bit 18: RTC_ALARM output type/PC13 value.

PC13MODE

Bit 19: PC13 mode.

PC14VALUE

Bit 20: PC14 value.

PC14MODE

Bit 21: PC14 mode.

PC15VALUE

Bit 22: PC15 value.

PC15MODE

Bit 23: PC15 mode.

ALRMASSR

alarm A sub second register

Offset: 0x44, reset: 0x00000000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
				MASKSS rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	SS rw

Toggle Fields.

SS

Bits 0-14: Sub seconds value.

MASKSS

Bits 24-27: Mask the most-significant bits starting at this bit.

BKP%sR

backup register

Offset: 0x50, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BKP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BKP rw

Toggle Fields.

BKP

Bits 0-31: BKP.

SCB

0xE000ED00: System control block

5/25 fields covered. Toggle Registers.

CPUID

CPUID base register

Offset: 0x0, reset: 0x410FC241, access: read-only

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
Implementer r								Variant r				Constant r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PartNo r												Revision r

Toggle Fields.

Revision

Bits 0-3: Revision number.

PartNo

Bits 4-15: Part number of the processor.

Constant

Bits 16-19: Reads as 0xF.

Variant

Bits 20-23: Variant number.

Implementer

Bits 24-31: Implementer code.

ICSR

Interrupt control and state register

Offset: 0x4, reset: 0x00000000, access: read-write

0/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
NMIPENDSET rw			PENDSVSET rw	PENDSVCLR rw	PENDSTSET rw	PENDSTCLR rw			ISRPENDING rw					VECTPENDING rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
VECTPENDING rw										VECTACTIVE rw

Toggle Fields.

VECTACTIVE

Bits 0-5: Active vector.

VECTPENDING

Bits 12-17: Pending vector.

ISRPENDING

Bit 22: Interrupt pending flag.

PENDSTCLR

Bit 25: SysTick exception clear-pending bit.

PENDSTSET

Bit 26: SysTick exception set-pending bit.

PENDSVCLR

Bit 27: PendSV clear-pending bit.

PENDSVSET

Bit 28: PendSV set-pending bit.

NMIPENDSET

Bit 31: NMI set-pending bit..

AIRCR

Application interrupt and reset control register

Offset: 0xC, reset: 0x00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
VECTKEYSTAT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ENDIANESS rw													SYSRESETREQ rw	VECTCLRACTIVE rw

Toggle Fields.

VECTCLRACTIVE

Bit 1: VECTCLRACTIVE.

SYSRESETREQ

Bit 2: SYSRESETREQ.

ENDIANESS

Bit 15: ENDIANESS.

VECTKEYSTAT

Bits 16-31: Register key.

SCR

System control register

Offset: 0x10, reset: 0x00000000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											SEVEONPEND rw		SLEEPDEEP rw	SLEEPONEXIT rw

Toggle Fields.

SLEEPONEXIT

Bit 1: SLEEPONEXIT.

SLEEPDEEP

Bit 2: SLEEPDEEP.

SEVEONPEND

Bit 4: Send Event on Pending bit.

CCR

Configuration and control register

Offset: 0x14, reset: 0x00000000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						STKALIGN rw						UNALIGN__TRP rw

Toggle Fields.

UNALIGN__TRP

Bit 3: UNALIGN_ TRP.

STKALIGN

Bit 9: STKALIGN.

SHPR2

System handler priority registers

Offset: 0x1C, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_11 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0

Toggle Fields.

PRI_11

Bits 24-31: Priority of system handler 11.

SHPR3

System handler priority registers

Offset: 0x20, reset: 0x00000000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
PRI_15 rw								PRI_14 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0

Toggle Fields.

PRI_14

Bits 16-23: Priority of system handler 14.

PRI_15

Bits 24-31: Priority of system handler 15.

SPI1

0x40013000: Serial peripheral interface

52/52 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

14/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BIDIMODE rw	BIDIOE rw	CRCEN rw	CRCNEXT rw	CRCL rw	RXONLY rw	SSM rw	SSI rw	LSBFIRST rw	SPE rw	BR rw			MSTR rw	CPOL rw	CPHA rw

Toggle Fields.

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

Allowed values:
0: Div2: f_PCLK / 2
1: Div4: f_PCLK / 4
2: Div8: f_PCLK / 8
3: Div16: f_PCLK / 16
4: Div32: f_PCLK / 32
5: Div64: f_PCLK / 64
6: Div128: f_PCLK / 128
7: Div256: f_PCLK / 256

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

Allowed values:
0: SlaveSelected: 0 is forced onto the NSS pin and the I/O value of the NSS pin is ignored
1: SlaveNotSelected: 1 is forced onto the NSS pin and the I/O value of the NSS pin is ignored

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	LDMA_TX rw	LDMA_RX rw	FRXTH rw	DS rw				TXEIE rw	RXNEIE rw	ERRIE rw	FRF rw	NSSP rw	SSOE rw	TXDMAEN rw	RXDMAEN rw

Toggle Fields.

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

Allowed values:
3: FourBit: 4-bit
4: FiveBit: 5-bit
5: SixBit: 6-bit
6: SevenBit: 7-bit
7: EightBit: 8-bit
8: NineBit: 9-bit
9: TenBit: 10-bit
10: ElevenBit: 11-bit
11: TwelveBit: 12-bit
12: ThirteenBit: 13-bit
13: FourteenBit: 14-bit
14: FifteenBit: 15-bit
15: SixteenBit: 16-bit

FRXTH

Bit 12: FIFO reception threshold.

Allowed values:
0: Half: RXNE event is generated if the FIFO level is greater than or equal to 1/2 (16-bit)
1: Quarter: RXNE event is generated if the FIFO level is greater than or equal to 1/4 (8-bit)

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, reset: 0x0002, access: Unspecified

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			FTLVL r		FRLVL r		FRE r	BSY r	OVR r	MODF r	CRCERR rw	UDR r	CHSIDE r	TXE r	RXNE r

Toggle Fields.

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

FRE

Bit 8: Frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

Bits 9-10: FIFO reception level.

Allowed values:
0: Empty: Rx FIFO Empty
1: Quarter: Rx 1/4 FIFO
2: Half: Rx 1/2 FIFO
3: Full: Rx FIFO full

FTLVL

Bits 11-12: FIFO transmission level.

Allowed values:
0: Empty: Tx FIFO Empty
1: Quarter: Tx 1/4 FIFO
2: Half: Tx 1/2 FIFO
3: Full: Tx FIFO full

DR

data register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DR rw

Toggle Fields.

DR

Bits 0-15: Data register.

Allowed values: 0-65535

CRCPR

CRC polynomial register

Offset: 0x10, reset: 0x0007, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CRCPOLY rw

Toggle Fields.

CRCPOLY

Bits 0-15: CRC polynomial register.

Allowed values: 0-65535

RXCRCR

RX CRC register

Offset: 0x14, reset: 0x0000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RxCRC r

Toggle Fields.

RxCRC

Bits 0-15: Rx CRC register.

Allowed values: 0-65535

TXCRCR

TX CRC register

Offset: 0x18, reset: 0x0000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TxCRC r

Toggle Fields.

TxCRC

Bits 0-15: Tx CRC register.

Allowed values: 0-65535

I2SCFGR

I2S configuration register

Offset: 0x1C, reset: 0x0000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				I2SMOD rw	I2SE rw	I2SCFG rw		PCMSYNC rw		I2SSTD rw		CKPOL rw	DATLEN rw		CHLEN rw

Toggle Fields.

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, reset: 0x00000010, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						MCKOE rw	ODD rw	I2SDIV rw

Toggle Fields.

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 2-255

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

SPI2

0x40003800: Serial peripheral interface

52/52 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

14/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BIDIMODE rw	BIDIOE rw	CRCEN rw	CRCNEXT rw	CRCL rw	RXONLY rw	SSM rw	SSI rw	LSBFIRST rw	SPE rw	BR rw			MSTR rw	CPOL rw	CPHA rw

Toggle Fields.

CPHA

Bit 0: Clock phase.

Allowed values:
0: FirstEdge: The first clock transition is the first data capture edge
1: SecondEdge: The second clock transition is the first data capture edge

CPOL

Bit 1: Clock polarity.

Allowed values:
0: IdleLow: CK to 0 when idle
1: IdleHigh: CK to 1 when idle

MSTR

Bit 2: Master selection.

Allowed values:
0: Slave: Slave configuration
1: Master: Master configuration

BR

Bits 3-5: Baud rate control.

SPE

Bit 6: SPI enable.

Allowed values:
0: Disabled: Peripheral disabled
1: Enabled: Peripheral enabled

LSBFIRST

Bit 7: Frame format.

Allowed values:
0: MSBFirst: Data is transmitted/received with the MSB first
1: LSBFirst: Data is transmitted/received with the LSB first

SSI

Bit 8: Internal slave select.

SSM

Bit 9: Software slave management.

Allowed values:
0: Disabled: Software slave management disabled
1: Enabled: Software slave management enabled

RXONLY

Bit 10: Receive only.

Allowed values:
0: FullDuplex: Full duplex (Transmit and receive)
1: OutputDisabled: Output disabled (Receive-only mode)

CRCL

Bit 11: CRC length.

Allowed values:
0: EightBit: 8-bit CRC length
1: SixteenBit: 16-bit CRC length

CRCNEXT

Bit 12: CRC transfer next.

Allowed values:
0: TxBuffer: Next transmit value is from Tx buffer
1: CRC: Next transmit value is from Tx CRC register

CRCEN

Bit 13: Hardware CRC calculation enable.

Allowed values:
0: Disabled: CRC calculation disabled
1: Enabled: CRC calculation enabled

BIDIOE

Bit 14: Output enable in bidirectional mode.

Allowed values:
0: OutputDisabled: Output disabled (receive-only mode)
1: OutputEnabled: Output enabled (transmit-only mode)

BIDIMODE

Bit 15: Bidirectional data mode enable.

Allowed values:
0: Unidirectional: 2-line unidirectional data mode selected
1: Bidirectional: 1-line bidirectional data mode selected

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	LDMA_TX rw	LDMA_RX rw	FRXTH rw	DS rw				TXEIE rw	RXNEIE rw	ERRIE rw	FRF rw	NSSP rw	SSOE rw	TXDMAEN rw	RXDMAEN rw

Toggle Fields.

RXDMAEN

Bit 0: Rx buffer DMA enable.

Allowed values:
0: Disabled: Rx buffer DMA disabled
1: Enabled: Rx buffer DMA enabled

TXDMAEN

Bit 1: Tx buffer DMA enable.

Allowed values:
0: Disabled: Tx buffer DMA disabled
1: Enabled: Tx buffer DMA enabled

SSOE

Bit 2: SS output enable.

Allowed values:
0: Disabled: SS output is disabled in master mode
1: Enabled: SS output is enabled in master mode

NSSP

Bit 3: NSS pulse management.

Allowed values:
0: NoPulse: No NSS pulse
1: PulseGenerated: NSS pulse generated

FRF

Bit 4: Frame format.

Allowed values:
0: Motorola: SPI Motorola mode
1: TI: SPI TI mode

ERRIE

Bit 5: Error interrupt enable.

Allowed values:
0: Masked: Error interrupt masked
1: NotMasked: Error interrupt not masked

RXNEIE

Bit 6: RX buffer not empty interrupt enable.

Allowed values:
0: Masked: RXE interrupt masked
1: NotMasked: RXE interrupt not masked

TXEIE

Bit 7: Tx buffer empty interrupt enable.

Allowed values:
0: Masked: TXE interrupt masked
1: NotMasked: TXE interrupt not masked

DS

Bits 8-11: Data size.

FRXTH

Bit 12: FIFO reception threshold.

LDMA_RX

Bit 13: Last DMA transfer for reception.

Allowed values:
0: Even: Number of data to transfer for receive is even
1: Odd: Number of data to transfer for receive is odd

LDMA_TX

Bit 14: Last DMA transfer for transmission.

Allowed values:
0: Even: Number of data to transfer for transmit is even
1: Odd: Number of data to transfer for transmit is odd

SR

status register

Offset: 0x8, reset: 0x0002, access: Unspecified

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			FTLVL r		FRLVL r		FRE r	BSY r	OVR r	MODF r	CRCERR rw	UDR r	CHSIDE r	TXE r	RXNE r

Toggle Fields.

RXNE

Bit 0: Receive buffer not empty.

Allowed values:
0: Empty: Rx buffer empty
1: NotEmpty: Rx buffer not empty

TXE

Bit 1: Transmit buffer empty.

Allowed values:
0: NotEmpty: Tx buffer not empty
1: Empty: Tx buffer empty

CHSIDE

Bit 2: Channel side.

Allowed values:
0: Left: Channel left has to be transmitted or has been received
1: Right: Channel right has to be transmitted or has been received

UDR

Bit 3: Underrun flag.

Allowed values:
0: NoUnderrun: No underrun occurred
1: Underrun: Underrun occurred

CRCERR

Bit 4: CRC error flag.

Allowed values:
0: Match: CRC value received matches the SPIx_RXCRCR value
1: NoMatch: CRC value received does not match the SPIx_RXCRCR value

MODF

Bit 5: Mode fault.

Allowed values:
0: NoFault: No mode fault occurred
1: Fault: Mode fault occurred

OVR

Bit 6: Overrun flag.

Allowed values:
0: NoOverrun: No overrun occurred
1: Overrun: Overrun occurred

BSY

Bit 7: Busy flag.

Allowed values:
0: NotBusy: SPI not busy
1: Busy: SPI busy

FRE

Bit 8: Frame format error.

Allowed values:
0: NoError: No frame format error
1: Error: A frame format error occurred

FRLVL

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
				I2SMOD rw	I2SE rw	I2SCFG rw		PCMSYNC rw		I2SSTD rw		CKPOL rw	DATLEN rw		CHLEN rw

Toggle Fields.

CHLEN

Bit 0: Channel length (number of bits per audio channel).

Allowed values:
0: SixteenBit: 16-bit wide
1: ThirtyTwoBit: 32-bit wide

DATLEN

Bits 1-2: Data length to be transferred.

Allowed values:
0: SixteenBit: 16-bit data length
1: TwentyFourBit: 24-bit data length
2: ThirtyTwoBit: 32-bit data length

CKPOL

Bit 3: Steady state clock polarity.

Allowed values:
0: IdleLow: I2S clock inactive state is low level
1: IdleHigh: I2S clock inactive state is high level

I2SSTD

Bits 4-5: I2S standard selection.

Allowed values:
0: Philips: I2S Philips standard
1: MSB: MSB justified standard
2: LSB: LSB justified standard
3: PCM: PCM standard

PCMSYNC

Bit 7: PCM frame synchronization.

Allowed values:
0: Short: Short frame synchronisation
1: Long: Long frame synchronisation

I2SCFG

Bits 8-9: I2S configuration mode.

Allowed values:
0: SlaveTx: Slave - transmit
1: SlaveRx: Slave - receive
2: MasterTx: Master - transmit
3: MasterRx: Master - receive

I2SE

Bit 10: I2S Enable.

Allowed values:
0: Disabled: I2S peripheral is disabled
1: Enabled: I2S peripheral is enabled

I2SMOD

Bit 11: I2S mode selection.

Allowed values:
0: SPIMode: SPI mode is selected
1: I2SMode: I2S mode is selected

I2SPR

I2S prescaler register

Offset: 0x20, reset: 0x00000010, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						MCKOE rw	ODD rw	I2SDIV rw

Toggle Fields.

I2SDIV

Bits 0-7: I2S Linear prescaler.

Allowed values: 2-255

ODD

Bit 8: Odd factor for the prescaler.

Allowed values:
0: Even: Real divider value is I2SDIV * 2
1: Odd: Real divider value is (I2SDIV * 2) + 1

MCKOE

Bit 9: Master clock output enable.

Allowed values:
0: Disabled: Master clock output is disabled
1: Enabled: Master clock output is enabled

STK

0xE000E010: SysTick timer

0/9 fields covered. Toggle Registers.

CSR

SysTick control and status register

Offset: 0x0, reset: 0X00000000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
															COUNTFLAG rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
													CLKSOURCE rw	TICKINT rw	ENABLE rw

Toggle Fields.

ENABLE

Bit 0: Counter enable.

TICKINT

Bit 1: SysTick exception request enable.

CLKSOURCE

Bit 2: Clock source selection.

COUNTFLAG

Bit 16: COUNTFLAG.

RVR

SysTick reload value register

Offset: 0x4, reset: 0X00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								RELOAD rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RELOAD rw

Toggle Fields.

RELOAD

Bits 0-23: RELOAD value.

CVR

SysTick current value register

Offset: 0x8, reset: 0X00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								CURRENT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CURRENT rw

Toggle Fields.

CURRENT

Bits 0-23: Current counter value.

CALIB

SysTick calibration value register

Offset: 0xC, reset: 0X00000000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
NOREF rw	SKEW rw							TENMS rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
TENMS rw

Toggle Fields.

TENMS

Bits 0-23: Calibration value.

SKEW

Bit 30: SKEW flag: Indicates whether the TENMS value is exact.

NOREF

Bit 31: NOREF flag. Reads as zero.

SYSCFG

0x40010000: System configuration controller

45/45 fields covered. Toggle Registers.

CFGR1

configuration register 1

Offset: 0x0, reset: 0x00000000, access: read-write

25/25 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
	TIM3_DMA_RMP rw	TIM2_DMA_RMP rw	TIM1_DMA_RMP rw	I2C1_DMA_RMP rw	USART3_DMA_RMP rw	USART2_DMA_RMP rw	SPI2_DMA_RMP rw	I2C_PA10_FMP rw	I2C_PA9_FMP rw	I2C2_FMP rw	I2C1_FMP rw	I2C_PB9_FMP rw	I2C_PB8_FMP rw	I2C_PB7_FMP rw	I2C_PB6_FMP rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TIM17_DMA_RMP2 rw	TIM16_DMA_RMP2 rw	TIM17_DMA_RMP rw	TIM16_DMA_RMP rw	USART1_RX_DMA_RMP rw	USART1_TX_DMA_RMP rw	ADC_DMA_RMP rw	IR_MOD rw			PA11_PA12_RMP rw			MEM_MODE rw

Toggle Fields.

MEM_MODE

Bits 0-1: Memory mapping selection bits.

Allowed values:
0: MainFlash: Main Flash memory mapped at 0x0000_0000
1: SystemFlash: System Flash memory mapped at 0x0000_0000
2: MainFlash2: Main Flash memory mapped at 0x0000_0000
3: SRAM: Embedded SRAM mapped at 0x0000_0000

PA11_PA12_RMP

Bit 4: PA11 and PA12 remapping bit for small packages (28 and 20 pins).

Allowed values:
0: NotRemapped: Pin pair PA9/PA10 mapped on the pins
1: Remapped: Pin pair PA11/PA12 mapped instead of PA9/PA10

IR_MOD

Bits 6-7: IR Modulation Envelope signal selection.

Allowed values:
0: TIM16: TIM16 selected
1: USART1: USART1 selected
2: USART4: USART4 selected

ADC_DMA_RMP

Bit 8: ADC DMA remapping bit.

Allowed values:
0: NotRemapped: ADC DMA request mapped on DMA channel 1
1: Remapped: ADC DMA request mapped on DMA channel 2

USART1_TX_DMA_RMP

Bit 9: USART1_TX DMA remapping bit.

Allowed values:
0: NotRemapped: USART1_TX DMA request mapped on DMA channel 2
1: Remapped: USART1_TX DMA request mapped on DMA channel 4

USART1_RX_DMA_RMP

Bit 10: USART1_RX DMA request remapping bit.

Allowed values:
0: NotRemapped: USART1_RX DMA request mapped on DMA channel 3
1: Remapped: USART1_RX DMA request mapped on DMA channel 5

TIM16_DMA_RMP

Bit 11: TIM16 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM16_CH1 and TIM16_UP DMA request mapped on DMA channel 3
1: Remapped: TIM16_CH1 and TIM16_UP DMA request mapped on DMA channel 4

TIM17_DMA_RMP

Bit 12: TIM17 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM17_CH1 and TIM17_UP DMA request mapped on DMA channel 1
1: Remapped: TIM17_CH1 and TIM17_UP DMA request mapped on DMA channel 2

TIM16_DMA_RMP2

Bit 13: TIM16 alternate DMA request remapping bit.

Allowed values:
0: NotAlternateRemapped: TIM16 DMA request mapped according to TIM16_DMA_RMP bit
1: AlternateRemapped: TIM16_CH1 and TIM16_UP DMA request mapped on DMA channel 6

TIM17_DMA_RMP2

Bit 14: TIM17 alternate DMA request remapping bit.

Allowed values:
0: NotAlternateRemapped: TIM17 DMA request mapped according to TIM16_DMA_RMP bit
1: AlternateRemapped: TIM17_CH1 and TIM17_UP DMA request mapped on DMA channel 7

I2C_PB6_FMP

Bit 16: Fast Mode Plus (FM plus) driving capability activation bits..

Allowed values:
0: Standard: PB6 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB6 and the Speed control is bypassed

I2C_PB7_FMP

Bit 17: Fast Mode Plus (FM+) driving capability activation bits..

Allowed values:
0: Standard: PB7 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB7 and the Speed control is bypassed

I2C_PB8_FMP

Bit 18: Fast Mode Plus (FM+) driving capability activation bits..

Allowed values:
0: Standard: PB8 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB8 and the Speed control is bypassed

I2C_PB9_FMP

Bit 19: Fast Mode Plus (FM+) driving capability activation bits..

Allowed values:
0: Standard: PB9 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PB9 and the Speed control is bypassed

I2C1_FMP

Bit 20: FM+ driving capability activation for I2C1.

Allowed values:
0: Standard: FM+ mode is controlled by I2C_Pxx_FMP bits only
1: FMP: FM+ mode is enabled on all I2C1 pins selected through selection bits in GPIOx_AFR registers

I2C2_FMP

Bit 21: FM+ driving capability activation for I2C2.

Allowed values:
0: Standard: FM+ mode is controlled by I2C_Pxx_FMP bits only
1: FMP: FM+ mode is enabled on all I2C2 pins selected through selection bits in GPIOx_AFR registers

I2C_PA9_FMP

Bit 22: Fast Mode Plus (FM+) driving capability activation bits.

Allowed values:
0: Standard: PA9 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PA9 and the Speed control is bypassed

I2C_PA10_FMP

Bit 23: Fast Mode Plus (FM+) driving capability activation bits.

Allowed values:
0: Standard: PA10 pin operate in standard mode
1: FMP: I2C FM+ mode enabled on PA10 and the Speed control is bypassed

SPI2_DMA_RMP

Bit 24: SPI2 DMA request remapping bit.

Allowed values:
0: NotRemapped: SPI2_RX and SPI2_TX DMA requests mapped on DMA channel 4 and 5 respectively
1: Remapped: SPI2_RX and SPI2_TX DMA requests mapped on DMA channel 6 and 7 respectively

USART2_DMA_RMP

Bit 25: USART2 DMA request remapping bit.

Allowed values:
0: NotRemapped: USART2_RX and USART2_TX DMA requests mapped on DMA channel 5 and 4 respectively
1: Remapped: USART2_RX and USART2_TX DMA requests mapped on DMA channel 6 and 7 respectively

USART3_DMA_RMP

Bit 26: USART3 DMA request remapping bit.

Allowed values:
0: NotRemapped: USART3_RX and USART3_TX DMA requests mapped on DMA channel 6 and 7 respectively (or simply disabled on STM32F0x0)
1: Remapped: USART3_RX and USART3_TX DMA requests mapped on DMA channel 3 and 2 respectively

I2C1_DMA_RMP

Bit 27: I2C1 DMA request remapping bit.

Allowed values:
0: NotRemapped: I2C1_RX and I2C1_TX DMA requests mapped on DMA channel 3 and 2 respectively
1: Remapped: I2C1_RX and I2C1_TX DMA requests mapped on DMA channel 7 and 6 respectively

TIM1_DMA_RMP

Bit 28: TIM1 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM1_CH1, TIM1_CH2 and TIM1_CH3 DMA requests mapped on DMA channel 2, 3 and 4 respectively
1: Remapped: TIM1_CH1, TIM1_CH2 and TIM1_CH3 DMA requests mapped on DMA channel 6

TIM2_DMA_RMP

Bit 29: TIM2 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM2_CH2 and TIM2_CH4 DMA requests mapped on DMA channel 3 and 4 respectively
1: Remapped: TIM2_CH2 and TIM2_CH4 DMA requests mapped on DMA channel 7

TIM3_DMA_RMP

Bit 30: TIM3 DMA request remapping bit.

Allowed values:
0: NotRemapped: TIM3_CH1 and TIM3_TRIG DMA requests mapped on DMA channel 4
1: Remapped: TIM3_CH1 and TIM3_TRIG DMA requests mapped on DMA channel 6

EXTICR1

external interrupt configuration register 1

Offset: 0x8, reset: 0x0000, access: read-write

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI3 rw				EXTI2 rw				EXTI1 rw				EXTI0 rw

Toggle Fields.

EXTI0

Bits 0-3: EXTI 0 configuration bits.

Allowed values:
4: PE0: Select PE0 as the source input for the EXTI0 external interrupt
0: PA0: Select PA0 as the source input for the EXTI0 external interrupt
1: PB0: Select PB0 as the source input for the EXTI0 external interrupt
2: PC0: Select PC0 as the source input for the EXTI0 external interrupt
3: PD0: Select PD0 as the source input for the EXTI0 external interrupt
5: PF0: Select PF0 as the source input for the EXTI0 external interrupt

EXTI1

Bits 4-7: EXTI 1 configuration bits.

Allowed values:
4: PE1: Select PE1 as the source input for the EXTI1 external interrupt
0: PA1: Select PA1 as the source input for the EXTI1 external interrupt
1: PB1: Select PB1 as the source input for the EXTI1 external interrupt
2: PC1: Select PC1 as the source input for the EXTI1 external interrupt
3: PD1: Select PD1 as the source input for the EXTI1 external interrupt
5: PF1: Select PF1 as the source input for the EXTI1 external interrupt

EXTI2

Bits 8-11: EXTI 2 configuration bits.

Allowed values:
4: PE2: Select PE2 as the source input for the EXTI2 external interrupt
0: PA2: Select PA2 as the source input for the EXTI2 external interrupt
1: PB2: Select PB2 as the source input for the EXTI2 external interrupt
2: PC2: Select PC2 as the source input for the EXTI2 external interrupt
3: PD2: Select PD2 as the source input for the EXTI2 external interrupt
5: PF2: Select PF2 as the source input for the EXTI2 external interrupt

EXTI3

Bits 12-15: EXTI 3 configuration bits.

Allowed values:
4: PE3: Select PE3 as the source input for the EXTI3 external interrupt
0: PA3: Select PA3 as the source input for the EXTI3 external interrupt
1: PB3: Select PB3 as the source input for the EXTI3 external interrupt
2: PC3: Select PC3 as the source input for the EXTI3 external interrupt
3: PD3: Select PD3 as the source input for the EXTI3 external interrupt
5: PF3: Select PF3 as the source input for the EXTI3 external interrupt

EXTICR2

external interrupt configuration register 2

Offset: 0xC, reset: 0x0000, access: read-write

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI7 rw				EXTI6 rw				EXTI5 rw				EXTI4 rw

Toggle Fields.

EXTI4

Bits 0-3: EXTI 4 configuration bits.

Allowed values:
4: PE4: Select PE4 as the source input for the EXTI4 external interrupt
0: PA4: Select PA4 as the source input for the EXTI4 external interrupt
1: PB4: Select PB4 as the source input for the EXTI4 external interrupt
2: PC4: Select PC4 as the source input for the EXTI4 external interrupt
3: PD4: Select PD4 as the source input for the EXTI4 external interrupt
5: PF4: Select PF4 as the source input for the EXTI4 external interrupt

EXTI5

Bits 4-7: EXTI 5 configuration bits.

Allowed values:
4: PE5: Select PE5 as the source input for the EXTI5 external interrupt
0: PA5: Select PA5 as the source input for the EXTI5 external interrupt
1: PB5: Select PB5 as the source input for the EXTI5 external interrupt
2: PC5: Select PC5 as the source input for the EXTI5 external interrupt
3: PD5: Select PD5 as the source input for the EXTI5 external interrupt
5: PF5: Select PF5 as the source input for the EXTI5 external interrupt

EXTI6

Bits 8-11: EXTI 6 configuration bits.

Allowed values:
4: PE6: Select PE6 as the source input for the EXTI6 external interrupt
0: PA6: Select PA6 as the source input for the EXTI6 external interrupt
1: PB6: Select PB6 as the source input for the EXTI6 external interrupt
2: PC6: Select PC6 as the source input for the EXTI6 external interrupt
3: PD6: Select PD6 as the source input for the EXTI6 external interrupt
5: PF6: Select PF6 as the source input for the EXTI6 external interrupt

EXTI7

Bits 12-15: EXTI 7 configuration bits.

Allowed values:
4: PE7: Select PE7 as the source input for the EXTI7 external interrupt
0: PA7: Select PA7 as the source input for the EXTI7 external interrupt
1: PB7: Select PB7 as the source input for the EXTI7 external interrupt
2: PC7: Select PC7 as the source input for the EXTI7 external interrupt
3: PD7: Select PD7 as the source input for the EXTI7 external interrupt
5: PF7: Select PF7 as the source input for the EXTI7 external interrupt

EXTICR3

external interrupt configuration register 3

Offset: 0x10, reset: 0x0000, access: read-write

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI11 rw				EXTI10 rw				EXTI9 rw				EXTI8 rw

Toggle Fields.

EXTI8

Bits 0-3: EXTI 8 configuration bits.

Allowed values:
4: PE8: Select PE8 as the source input for the EXTI8 external interrupt
0: PA8: Select PA8 as the source input for the EXTI8 external interrupt
1: PB8: Select PB8 as the source input for the EXTI8 external interrupt
2: PC8: Select PC8 as the source input for the EXTI8 external interrupt
3: PD8: Select PD8 as the source input for the EXTI8 external interrupt
5: PF8: Select PF8 as the source input for the EXTI8 external interrupt

EXTI9

Bits 4-7: EXTI 9 configuration bits.

Allowed values:
4: PE9: Select PE9 as the source input for the EXTI9 external interrupt
0: PA9: Select PA9 as the source input for the EXTI9 external interrupt
1: PB9: Select PB9 as the source input for the EXTI9 external interrupt
2: PC9: Select PC9 as the source input for the EXTI9 external interrupt
3: PD9: Select PD9 as the source input for the EXTI9 external interrupt
5: PF9: Select PF9 as the source input for the EXTI9 external interrupt

EXTI10

Bits 8-11: EXTI 10 configuration bits.

Allowed values:
4: PE10: Select PE10 as the source input for the EXTI10 external interrupt
0: PA10: Select PA10 as the source input for the EXTI10 external interrupt
1: PB10: Select PB10 as the source input for the EXTI10 external interrupt
2: PC10: Select PC10 as the source input for the EXTI10 external interrupt
3: PD10: Select PD10 as the source input for the EXTI10 external interrupt
5: PF10: Select PF10 as the source input for the EXTI10 external interrupt

EXTI11

Bits 12-15: EXTI 11 configuration bits.

Allowed values:
4: PE11: Select PE11 as the source input for the EXTI11 external interrupt
0: PA11: Select PA11 as the source input for the EXTI11 external interrupt
1: PB11: Select PB11 as the source input for the EXTI11 external interrupt
2: PC11: Select PC11 as the source input for the EXTI11 external interrupt
3: PD11: Select PD11 as the source input for the EXTI11 external interrupt
5: PF11: Select PF11 as the source input for the EXTI11 external interrupt

EXTICR4

external interrupt configuration register 4

Offset: 0x14, reset: 0x0000, access: read-write

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
EXTI15 rw				EXTI14 rw				EXTI13 rw				EXTI12 rw

Toggle Fields.

EXTI12

Bits 0-3: EXTI 12 configuration bits.

Allowed values:
4: PE12: Select PE12 as the source input for the EXTI12 external interrupt
0: PA12: Select PA12 as the source input for the EXTI12 external interrupt
1: PB12: Select PB12 as the source input for the EXTI12 external interrupt
2: PC12: Select PC12 as the source input for the EXTI12 external interrupt
3: PD12: Select PD12 as the source input for the EXTI12 external interrupt
5: PF12: Select PF12 as the source input for the EXTI12 external interrupt

EXTI13

Bits 4-7: EXTI 13 configuration bits.

Allowed values:
4: PE13: Select PE13 as the source input for the EXTI13 external interrupt
0: PA13: Select PA13 as the source input for the EXTI13 external interrupt
1: PB13: Select PB13 as the source input for the EXTI13 external interrupt
2: PC13: Select PC13 as the source input for the EXTI13 external interrupt
3: PD13: Select PD13 as the source input for the EXTI13 external interrupt
5: PF13: Select PF13 as the source input for the EXTI13 external interrupt

EXTI14

Bits 8-11: EXTI 14 configuration bits.

Allowed values:
4: PE14: Select PE14 as the source input for the EXTI14 external interrupt
0: PA14: Select PA14 as the source input for the EXTI14 external interrupt
1: PB14: Select PB14 as the source input for the EXTI14 external interrupt
2: PC14: Select PC14 as the source input for the EXTI14 external interrupt
3: PD14: Select PD14 as the source input for the EXTI14 external interrupt
5: PF14: Select PF14 as the source input for the EXTI14 external interrupt

EXTI15

Bits 12-15: EXTI 15 configuration bits.

Allowed values:
4: PE15: Select PE15 as the source input for the EXTI15 external interrupt
0: PA15: Select PA15 as the source input for the EXTI15 external interrupt
1: PB15: Select PB15 as the source input for the EXTI15 external interrupt
2: PC15: Select PC15 as the source input for the EXTI15 external interrupt
3: PD15: Select PD15 as the source input for the EXTI15 external interrupt
5: PF15: Select PF15 as the source input for the EXTI15 external interrupt

CFGR2

configuration register 2

Offset: 0x18, reset: 0x0000, access: read-write

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							SRAM_PEF rw						PVD_LOCK rw	SRAM_PARITY_LOCK rw	LOCKUP_LOCK rw

Toggle Fields.

LOCKUP_LOCK

Bit 0: Cortex-M0 LOCKUP bit enable bit.

Allowed values:
0: Disconnected: Cortex-M0 LOCKUP output disconnected from TIM1/15/16/17 Break input
1: Connected: Cortex-M0 LOCKUP output connected to TIM1/15/16/17 Break input

SRAM_PARITY_LOCK

Bit 1: SRAM parity lock bit.

Allowed values:
0: Disconnected: SRAM parity error disconnected from TIM1/15/16/17 Break input
1: Connected: SRAM parity error connected to TIM1/15/16/17 Break input

PVD_LOCK

Bit 2: PVD lock enable bit.

Allowed values:
0: Disconnected: PVD interrupt disconnected from TIM1/15/16/17 Break input
1: Connected: PVD interrupt connected to TIM1/15/16/17 Break input

SRAM_PEF

Bit 8: SRAM parity flag.

Allowed values:
0: NoParityError: No SRAM parity error detected
1: ParityErrorDetected: SRAM parity error detected

TIM1

0x40012C00: Advanced-timers

77/124 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

Allowed values:
0: AnyEvent: Any of counter overflow/underflow, setting UG, or update through slave mode, generates an update interrupt or DMA request
1: CounterOnly: Only counter overflow/underflow generates an update interrupt or DMA request

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

Allowed values:
0: EdgeAligned: The counter counts up or down depending on the direction bit
1: CenterAligned1: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting down.
2: CenterAligned2: The counter counts up and down alternatively. Output compare interrupt flags are set only when the counter is counting up.
3: CenterAligned3: The counter counts up and down alternatively. Output compare interrupt flags are set both when the counter is counting up or down.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

3/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	OIS4 rw	OIS3N rw	OIS3 rw	OIS2N rw	OIS2 rw	OIS1N rw	OIS1 rw	TI1S rw	MMS rw			CCDS rw	CCUS rw		CCPC rw

Toggle Fields.

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: The UG bit from the TIMx_EGR register is used as trigger output
1: Enable: The counter enable signal, CNT_EN, is used as trigger output
2: Update: The update event is selected as trigger output
3: ComparePulse: The trigger output send a positive pulse when the CC1IF flag it to be set, as soon as a capture or a compare match occurred
4: CompareOC1: OC1REF signal is used as trigger output
5: CompareOC2: OC2REF signal is used as trigger output
6: CompareOC3: OC3REF signal is used as trigger output
7: CompareOC4: OC4REF signal is used as trigger output

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

OIS1

Bit 8: Output Idle state 1.

OIS1N

Bit 9: Output Idle state 1.

OIS2

Bit 10: Output Idle state 2.

OIS2N

Bit 11: Output Idle state 2.

OIS3

Bit 12: Output Idle state 3.

OIS3N

Bit 13: Output Idle state 3.

OIS4

Bit 14: Output Idle state 4.

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS rw				SMS rw

Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

Allowed values:
0: Disabled: Slave mode disabled - if CEN = ‘1 then the prescaler is clocked directly by the internal clock.
1: Encoder_Mode_1: Encoder mode 1 - Counter counts up/down on TI2FP1 edge depending on TI1FP2 level.
2: Encoder_Mode_2: Encoder mode 2 - Counter counts up/down on TI1FP2 edge depending on TI2FP1 level.
3: Encoder_Mode_3: Encoder mode 3 - Counter counts up/down on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
4: Reset_Mode: Reset Mode - Rising edge of the selected trigger input (TRGI) reinitializes the counter and generates an update of the registers.
5: Gated_Mode: Gated Mode - The counter clock is enabled when the trigger input (TRGI) is high. The counter stops (but is not reset) as soon as the trigger becomes low. Both start and stop of the counter are controlled.
6: Trigger_Mode: Trigger Mode - The counter starts at a rising edge of the trigger TRGI (but it is not reset). Only the start of the counter is controlled.
7: Ext_Clock_Mode: External Clock Mode 1 - Rising edges of the selected trigger (TRGI) clock the counter.

TS

Bits 4-6: Trigger selection.

Allowed values:
0: ITR0: Internal Trigger 0 (ITR0)
1: ITR1: Internal Trigger 1 (ITR1)
2: ITR2: Internal Trigger 2 (ITR2)
4: TI1F_ED: TI1 Edge Detector (TI1F_ED)
5: TI1FP1: Filtered Timer Input 1 (TI1FP1)
6: TI2FP2: Filtered Timer Input 2 (TI2FP2)
7: ETRF: External Trigger input (ETRF)

MSM

Bit 7: Master/Slave mode.

Allowed values:
0: NoSync: No action
1: Sync: The effect of an event on the trigger input (TRGI) is delayed to allow a perfect synchronization between the current timer and its slaves (through TRGO). It is useful if we want to synchronize several timers on a single external event.

ETF

Bits 8-11: External trigger filter.

Allowed values:
0: NoFilter: No filter, sampling is done at fDTS
1: FCK_INT_N2: fSAMPLING=fCK_INT, N=2
2: FCK_INT_N4: fSAMPLING=fCK_INT, N=4
3: FCK_INT_N8: fSAMPLING=fCK_INT, N=8
4: FDTS_Div2_N6: fSAMPLING=fDTS/2, N=6
5: FDTS_Div2_N8: fSAMPLING=fDTS/2, N=8
6: FDTS_Div4_N6: fSAMPLING=fDTS/4, N=6
7: FDTS_Div4_N8: fSAMPLING=fDTS/4, N=8
8: FDTS_Div8_N6: fSAMPLING=fDTS/8, N=6
9: FDTS_Div8_N8: fSAMPLING=fDTS/8, N=8
10: FDTS_Div16_N5: fSAMPLING=fDTS/16, N=5
11: FDTS_Div16_N6: fSAMPLING=fDTS/16, N=6
12: FDTS_Div16_N8: fSAMPLING=fDTS/16, N=8
13: FDTS_Div32_N5: fSAMPLING=fDTS/32, N=5
14: FDTS_Div32_N6: fSAMPLING=fDTS/32, N=6
15: FDTS_Div32_N8: fSAMPLING=fDTS/32, N=8

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

12/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw	COMDE rw	CC4DE rw	CC3DE rw	CC2DE rw	CC1DE rw	UDE rw	BIE rw	TIE rw	COMIE rw	CC4IE rw	CC3IE rw	CC2IE rw	CC1IE rw	UIE rw

Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC3IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC4IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

COMIE

Bit 5: COM interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC3DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC4DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

10/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CC4OF rw	CC3OF rw	CC2OF rw	CC1OF rw		BIF rw	TIF rw	COMIF rw	CC4IF rw	CC3IF rw	CC2IF rw	CC1IF rw	UIF rw

Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

Allowed values:
1: Match: If CC1 is an output: The content of the counter TIMx_CNT matches the content of the TIMx_CCR1 register. If CC1 is an input: The counter value has been captured in TIMx_CCR1 register.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

CC3IF

Bit 3: Capture/Compare 3 interrupt flag.

CC4IF

Bit 4: Capture/Compare 4 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

BIF

Bit 7: Break interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC3OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC4OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

6/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								BG w	TG w	COMG w	CC4G w	CC3G w	CC2G w	CC1G w	UG w

Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC1G

Bit 1: Capture/compare 1 generation.

Allowed values:
1: Trigger: If CC1 is an output: CC1IF flag is set, Corresponding interrupt or DMA request is sent if enabled. If CC1 is an input: The current value of the counter is captured in TIMx_CCR1 register.

CC2G

Bit 2: Capture/compare 2 generation.

CC3G

Bit 3: Capture/compare 3 generation.

CC4G

Bit 4: Capture/compare 4 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

4/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC2F rw				IC2PSC rw		CC2S rw		IC1F rw				IC1PSC rw		CC1S rw

Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

Allowed values:
1: TI1: CC1 channel is configured as input, IC1 is mapped on TI1
2: TI2: CC1 channel is configured as input, IC1 is mapped on TI2
3: TRC: CC1 channel is configured as input, IC1 is mapped on TRC

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CC2S

Bits 8-9: Capture/Compare 2 selection.

Allowed values:
1: TI2: CC2 channel is configured as input, IC2 is mapped on TI2
2: TI1: CC2 channel is configured as input, IC2 is mapped on TI1
3: TRC: CC2 channel is configured as input, IC2 is mapped on TRC

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

Allowed values: 0-15

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1C, reset: 0x00000000, access: read-write

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC4F rw				IC4PSC rw		CC4S rw		IC3F rw				IC3PSC rw		CC3S rw

Toggle Fields.

CC3S

Bits 0-1: Capture/compare 3 selection.

Allowed values:
1: TI3: CC3 channel is configured as input, IC3 is mapped on TI3
2: TI4: CC3 channel is configured as input, IC3 is mapped on TI4
3: TRC: CC3 channel is configured as input, IC3 is mapped on TRC

IC3PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0-3

IC3F

Bits 4-7: Input capture 3 filter.

Allowed values: 0-15

CC4S

Bits 8-9: Capture/Compare 4 selection.

Allowed values:
1: TI4: CC4 channel is configured as input, IC4 is mapped on TI4
2: TI3: CC4 channel is configured as input, IC4 is mapped on TI3
3: TRC: CC4 channel is configured as input, IC4 is mapped on TRC

IC4PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0-3

IC4F

Bits 12-15: Input capture 4 filter.

Allowed values: 0-15

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/14 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CC4P rw	CC4E rw	CC3NP rw	CC3NE rw	CC3P rw	CC3E rw	CC2NP rw	CC2NE rw	CC2P rw	CC2E rw	CC1NP rw	CC1NE rw	CC1P rw	CC1E rw

Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NE

Bit 2: Capture/Compare 1 complementary output enable.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NE

Bit 6: Capture/Compare 2 complementary output enable.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CC3E

Bit 8: Capture/Compare 3 output enable.

CC3P

Bit 9: Capture/Compare 3 output Polarity.

CC3NE

Bit 10: Capture/Compare 3 complementary output enable.

CC3NP

Bit 11: Capture/Compare 3 output Polarity.

CC4E

Bit 12: Capture/Compare 4 output enable.

CC4P

Bit 13: Capture/Compare 3 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle Fields.

CNT

Bits 0-15: counter value.

Allowed values: 0-65535

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0-65535

RCR

repetition counter register

Offset: 0x30, reset: 0x0000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REP rw

Toggle Fields.

REP

Bits 0-7: Repetition counter value.

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle Fields.

CCR

Bits 0-15: Capture/Compare 1 value.

Allowed values: 0-65535

BDTR

break and dead-time register

Offset: 0x44, reset: 0x0000, access: read-write

3/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle Fields.

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are forced to idle level

OSSR

Bit 11: Off-state selection for Run mode.

Allowed values:
0: Disabled: When inactive, OC/OCN outputs are disabled
1: IdleLevel: When inactive, OC/OCN outputs are enabled with their inactive level

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

Allowed values:
0: DisabledIdle: OC/OCN are disabled or forced idle depending on OSSI
1: Enabled: OC/OCN are enabled if CCxE/CCxNE are set

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle Fields.

DBA

Bits 0-4: DMA base address.

Allowed values: 0-31

DBL

Bits 8-12: DMA burst length.

Allowed values: 0-18

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

TIM14

0x40002000: General-purpose-timers

9/27 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CKD rw		ARPE rw					URS rw	UDIS rw	CEN rw

Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														CC1IE rw	UIE rw

Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CC1OF rw								CC1IF rw	UIF rw

Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														CC1G w	UG w

Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC1G

Bit 1: Capture/compare 1 generation.

CCMR1_Input

capture/compare mode register (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								IC1F rw				IC1PSC rw		CC1S rw

Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												CC1NP rw		CC1P rw	CC1E rw

Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle Fields.

CNT

Bits 0-15: counter value.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle Fields.

CCR

Bits 0-15: Capture/Compare 1 value.

OR

option register

Offset: 0x50, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														RMP rw

Toggle Fields.

RMP

Bits 0-1: Timer input 1 remap.

TIM15

0x40014000: General-purpose-timers

9/78 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

5/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CKD rw		ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

OPM

Bit 3: One-pulse mode.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					OIS2 rw	OIS1N rw	OIS1 rw		MMS rw			CCDS rw	CCUS rw		CCPC rw

Toggle Fields.

CCPC

Bit 0: Capture/compare preloaded control.

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

MMS

Bits 4-6: Master mode selection.

OIS1

Bit 8: Output Idle state 1.

OIS1N

Bit 9: Output Idle state 1.

OIS2

Bit 10: Output Idle state 2.

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								MSM rw	TS rw				SMS rw

Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

TS

Bits 4-6: Trigger selection.

MSM

Bit 7: Master/Slave mode.

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

1/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw				CC2DE rw	CC1DE rw	UDE rw	BIE rw	TIE rw	COMIE rw			CC2IE rw	CC1IE rw	UIE rw

Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

COMIE

Bit 5: COM interrupt enable.

TIE

Bit 6: Trigger interrupt enable.

BIE

Bit 7: Break interrupt enable.

UDE

Bit 8: Update DMA request enable.

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
					CC2OF rw	CC1OF rw		BIF rw	TIF rw	COMIF rw			CC2IF rw	CC1IF rw	UIF rw

Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								BG w	TG w	COMG w			CC2G w	CC1G w	UG w

Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC1G

Bit 1: Capture/compare 1 generation.

CC2G

Bit 2: Capture/compare 2 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

0/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC2F rw				IC2PSC rw		CC2S rw		IC1F rw				IC1PSC rw		CC1S rw

Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CC2S

Bits 8-9: Capture/Compare 2 selection.

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								CC2NP rw		CC2P rw	CC2E rw	CC1NP rw	CC1NE rw	CC1P rw	CC1E rw

Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NE

Bit 2: Capture/Compare 1 complementary output enable.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle Fields.

CNT

Bits 0-15: counter value.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, reset: 0x0000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REP rw

Toggle Fields.

REP

Bits 0-7: Repetition counter value.

CCR1

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR1 rw

Toggle Fields.

CCR1

Bits 0-15: Capture/Compare 1 value.

CCR2

capture/compare register 2

Offset: 0x38, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR2 rw

Toggle Fields.

CCR2

Bits 0-15: Capture/Compare 2 value.

BDTR

break and dead-time register

Offset: 0x44, reset: 0x0000, access: read-write

0/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle Fields.

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle Fields.

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

TIM16

0x40014400: General-purpose-timers

19/57 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CKD rw		ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

OPM

Bit 3: One-pulse mode.

Allowed values:
0: NotStopped: Not stopped at update event
1: Stopped: Counter stops counting at next update event

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						OIS1N rw	OIS1 rw					CCDS rw	CCUS rw		CCPC rw

Toggle Fields.

CCPC

Bit 0: Capture/compare preloaded control.

Allowed values:
0: NotPreloaded: CCxE, CCxNE and OCxM bits are not preloaded
1: Preloaded: CCxE, CCxNE and OCxM bits are preloaded

CCUS

Bit 2: Capture/compare control update selection.

Allowed values:
0: Default: Capture/compare are updated only by setting the COMG bit
1: WithRisingEdge: Capture/compare are updated by setting the COMG bit or when an rising edge occurs on TRGI

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

OIS1

Bit 8: Output Idle state 1.

Allowed values:
0: Low: OC1=0 (after a dead-time if OC1N is implemented) when MOE=0
1: High: OC1=1 (after a dead-time if OC1N is implemented) when MOE=0

OIS1N

Bit 9: Output Idle state 1.

Allowed values:
0: Low: OC1N=0 after a dead-time when MOE=0
1: High: OC1N=1 after a dead-time when MOE=0

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

5/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw					CC1DE rw	UDE rw	BIE rw	TIE rw	COMIE rw				CC1IE rw	UIE rw

Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CC1 interrupt disabled
1: Enabled: CC1 interrupt enabled

COMIE

Bit 5: COM interrupt enable.

Allowed values:
0: Disabled: COM interrupt disabled
1: Enabled: COM interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

BIE

Bit 7: Break interrupt enable.

Allowed values:
0: Disabled: Break interrupt disabled
1: Enabled: Break interrupt enabled

UDE

Bit 8: Update DMA request enable.

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CC1 DMA request disabled
1: Enabled: CC1 DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CC1OF rw		BIF rw	TIF rw	COMIF rw				CC1IF rw	UIF rw

Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								BG w	TG w	COMG w				CC1G w	UG w

Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC1G

Bit 1: Capture/compare 1 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								IC1F rw				IC1PSC rw		CC1S rw

Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												CC1NP rw	CC1NE rw	CC1P rw	CC1E rw

Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NE

Bit 2: Capture/Compare 1 complementary output enable.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle Fields.

CNT

Bits 0-15: counter value.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, reset: 0x0000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REP rw

Toggle Fields.

REP

Bits 0-7: Repetition counter value.

CCR1

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR1 rw

Toggle Fields.

CCR1

Bits 0-15: Capture/Compare 1 value.

BDTR

break and dead-time register

Offset: 0x44, reset: 0x0000, access: read-write

0/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle Fields.

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle Fields.

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

TIM17

0x40014800: General-purpose-timers

19/57 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CKD rw		ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

OPM

Bit 3: One-pulse mode.

Allowed values:
0: NotStopped: Not stopped at update event
1: Stopped: Counter stops counting at next update event

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						OIS1N rw	OIS1 rw					CCDS rw	CCUS rw		CCPC rw

Toggle Fields.

CCPC

Bit 0: Capture/compare preloaded control.

Allowed values:
0: NotPreloaded: CCxE, CCxNE and OCxM bits are not preloaded
1: Preloaded: CCxE, CCxNE and OCxM bits are preloaded

CCUS

Bit 2: Capture/compare control update selection.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

OIS1

Bit 8: Output Idle state 1.

Allowed values:
0: Low: OC1=0 (after a dead-time if OC1N is implemented) when MOE=0
1: High: OC1=1 (after a dead-time if OC1N is implemented) when MOE=0

OIS1N

Bit 9: Output Idle state 1.

Allowed values:
0: Low: OC1N=0 after a dead-time when MOE=0
1: High: OC1N=1 after a dead-time when MOE=0

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

5/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw					CC1DE rw	UDE rw	BIE rw	TIE rw	COMIE rw				CC1IE rw	UIE rw

Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CC1 interrupt disabled
1: Enabled: CC1 interrupt enabled

COMIE

Bit 5: COM interrupt enable.

Allowed values:
0: Disabled: COM interrupt disabled
1: Enabled: COM interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

BIE

Bit 7: Break interrupt enable.

Allowed values:
0: Disabled: Break interrupt disabled
1: Enabled: Break interrupt enabled

UDE

Bit 8: Update DMA request enable.

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CC1 DMA request disabled
1: Enabled: CC1 DMA request enabled

TDE

Bit 14: Trigger DMA request enable.

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

1/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CC1OF rw		BIF rw	TIF rw	COMIF rw				CC1IF rw	UIF rw

Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

COMIF

Bit 5: COM interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

BIF

Bit 7: Break interrupt flag.

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

1/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								BG w	TG w	COMG w				CC1G w	UG w

Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC1G

Bit 1: Capture/compare 1 generation.

COMG

Bit 5: Capture/Compare control update generation.

TG

Bit 6: Trigger generation.

BG

Bit 7: Break generation.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

0/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								IC1F rw				IC1PSC rw		CC1S rw

Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
												CC1NP rw	CC1NE rw	CC1P rw	CC1E rw

Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NE

Bit 2: Capture/Compare 1 complementary output enable.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle Fields.

CNT

Bits 0-15: counter value.

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

RCR

repetition counter register

Offset: 0x30, reset: 0x0000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								REP rw

Toggle Fields.

REP

Bits 0-7: Repetition counter value.

CCR1

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR1 rw

Toggle Fields.

CCR1

Bits 0-15: Capture/Compare 1 value.

BDTR

break and dead-time register

Offset: 0x44, reset: 0x0000, access: read-write

0/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
MOE rw	AOE rw	BKP rw	BKE rw	OSSR rw	OSSI rw	LOCK rw		DTG rw

Toggle Fields.

DTG

Bits 0-7: Dead-time generator setup.

LOCK

Bits 8-9: Lock configuration.

OSSI

Bit 10: Off-state selection for Idle mode.

OSSR

Bit 11: Off-state selection for Run mode.

BKE

Bit 12: Break enable.

BKP

Bit 13: Break polarity.

AOE

Bit 14: Automatic output enable.

MOE

Bit 15: Main output enable.

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle Fields.

DBA

Bits 0-4: DMA base address.

DBL

Bits 8-12: DMA burst length.

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAB rw

Toggle Fields.

DMAB

Bits 0-15: DMA register for burst accesses.

TIM2

0x40000000: General-purpose-timers

74/98 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TI1S rw	MMS rw			CCDS rw

Toggle Fields.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS rw				SMS rw

Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

TS

Bits 4-6: Trigger selection.

MSM

Bit 7: Master/Slave mode.

ETF

Bits 8-11: External trigger filter.

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

12/13 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw	COMDE rw	CC4DE rw	CC3DE rw	CC2DE rw	CC1DE rw	UDE rw		TIE rw		CC4IE rw	CC3IE rw	CC2IE rw	CC1IE rw	UIE rw

Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC3IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC4IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC3DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC4DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CC4OF rw	CC3OF rw	CC2OF rw	CC1OF rw			TIF rw		CC4IF rw	CC3IF rw	CC2IF rw	CC1IF rw	UIF rw

Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

CC3IF

Bit 3: Capture/Compare 3 interrupt flag.

CC4IF

Bit 4: Capture/Compare 4 interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC3OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC4OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									TG w		CC4G w	CC3G w	CC2G w	CC1G w	UG w

Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC1G

Bit 1: Capture/compare 1 generation.

CC2G

Bit 2: Capture/compare 2 generation.

CC3G

Bit 3: Capture/compare 3 generation.

CC4G

Bit 4: Capture/compare 4 generation.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

4/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC2F rw				IC2PSC rw		CC2S rw		IC1F rw				IC1PSC rw		CC1S rw

Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CC2S

Bits 8-9: Capture/compare 2 selection.

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

Allowed values: 0-15

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1C, reset: 0x00000000, access: read-write

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC4F rw				IC4PSC rw		CC4S rw		IC3F rw				IC3PSC rw		CC3S rw

Toggle Fields.

CC3S

Bits 0-1: Capture/Compare 3 selection.

IC3PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0-3

IC3F

Bits 4-7: Input capture 3 filter.

Allowed values: 0-15

CC4S

Bits 8-9: Capture/Compare 4 selection.

IC4PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0-3

IC4F

Bits 12-15: Input capture 4 filter.

Allowed values: 0-15

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CC4NP rw		CC4P rw	CC4E rw	CC3NP rw		CC3P rw	CC3E rw	CC2NP rw		CC2P rw	CC2E rw	CC1NP rw		CC1P rw	CC1E rw

Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CC3E

Bit 8: Capture/Compare 3 output enable.

CC3P

Bit 9: Capture/Compare 3 output Polarity.

CC3NP

Bit 11: Capture/Compare 3 output Polarity.

CC4E

Bit 12: Capture/Compare 4 output enable.

CC4P

Bit 13: Capture/Compare 3 output Polarity.

CC4NP

Bit 15: Capture/Compare 4 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle Fields.

CNT

Bits 0-31: Counter value.

Allowed values: 0-4294967295

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ARR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle Fields.

ARR

Bits 0-31: Auto-reload value.

Allowed values: 0-4294967295

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CCR rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle Fields.

CCR

Bits 0-31: Capture/Compare 1 value.

Allowed values: 0-4294967295

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle Fields.

DBA

Bits 0-4: DMA base address.

Allowed values: 0-31

DBL

Bits 8-12: DMA burst length.

Allowed values: 0-18

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAR rw

Toggle Fields.

DMAR

Bits 0-15: DMA register for burst accesses.

TIM3

0x40000400: General-purpose-timers

74/101 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

8/8 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						CKD rw		ARPE rw	CMS rw		DIR rw	OPM rw	URS rw	UDIS rw	CEN rw

Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

DIR

Bit 4: Direction.

Allowed values:
0: Up: Counter used as upcounter
1: Down: Counter used as downcounter

CMS

Bits 5-6: Center-aligned mode selection.

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CKD

Bits 8-9: Clock division.

Allowed values:
0: Div1: t_DTS = t_CK_INT
1: Div2: t_DTS = 2 × t_CK_INT
2: Div4: t_DTS = 4 × t_CK_INT

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								TI1S rw	MMS rw			CCDS rw

Toggle Fields.

CCDS

Bit 3: Capture/compare DMA selection.

Allowed values:
0: OnCompare: CCx DMA request sent when CCx event occurs
1: OnUpdate: CCx DMA request sent when update event occurs

MMS

Bits 4-6: Master mode selection.

TI1S

Bit 7: TI1 selection.

Allowed values:
0: Normal: The TIMx_CH1 pin is connected to TI1 input
1: XOR: The TIMx_CH1, CH2, CH3 pins are connected to TI1 input

SMCR

slave mode control register

Offset: 0x8, reset: 0x0000, access: read-write

7/7 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ETP rw	ECE rw	ETPS rw		ETF rw				MSM rw	TS rw				SMS rw

Toggle Fields.

SMS

Bits 0-2: Slave mode selection.

TS

Bits 4-6: Trigger selection.

MSM

Bit 7: Master/Slave mode.

ETF

Bits 8-11: External trigger filter.

ETPS

Bits 12-13: External trigger prescaler.

Allowed values:
0: Div1: Prescaler OFF
1: Div2: ETRP frequency divided by 2
2: Div4: ETRP frequency divided by 4
3: Div8: ETRP frequency divided by 8

ECE

Bit 14: External clock enable.

Allowed values:
0: Disabled: External clock mode 2 disabled
1: Enabled: External clock mode 2 enabled. The counter is clocked by any active edge on the ETRF signal.

ETP

Bit 15: External trigger polarity.

Allowed values:
0: NotInverted: ETR is noninverted, active at high level or rising edge
1: Inverted: ETR is inverted, active at low level or falling edge

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

12/13 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
	TDE rw	COMDE rw	CC4DE rw	CC3DE rw	CC2DE rw	CC1DE rw	UDE rw		TIE rw		CC4IE rw	CC3IE rw	CC2IE rw	CC1IE rw	UIE rw

Toggle Fields.

UIE

Bit 0: Update interrupt enable.

Allowed values:
0: Disabled: Update interrupt disabled
1: Enabled: Update interrupt enabled

CC1IE

Bit 1: Capture/Compare 1 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC2IE

Bit 2: Capture/Compare 2 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC3IE

Bit 3: Capture/Compare 3 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

CC4IE

Bit 4: Capture/Compare 4 interrupt enable.

Allowed values:
0: Disabled: CCx interrupt disabled
1: Enabled: CCx interrupt enabled

TIE

Bit 6: Trigger interrupt enable.

Allowed values:
0: Disabled: Trigger interrupt disabled
1: Enabled: Trigger interrupt enabled

UDE

Bit 8: Update DMA request enable.

Allowed values:
0: Disabled: Update DMA request disabled
1: Enabled: Update DMA request enabled

CC1DE

Bit 9: Capture/Compare 1 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC2DE

Bit 10: Capture/Compare 2 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC3DE

Bit 11: Capture/Compare 3 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

CC4DE

Bit 12: Capture/Compare 4 DMA request enable.

Allowed values:
0: Disabled: CCx DMA request disabled
1: Enabled: CCx DMA request enabled

COMDE

Bit 13: COM DMA request enable.

TDE

Bit 14: Trigger DMA request enable.

Allowed values:
0: Disabled: Trigger DMA request disabled
1: Enabled: Trigger DMA request enabled

SR

status register

Offset: 0x10, reset: 0x0000, access: read-write

10/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			CC4OF rw	CC3OF rw	CC2OF rw	CC1OF rw			TIF rw		CC4IF rw	CC3IF rw	CC2IF rw	CC1IF rw	UIF rw

Toggle Fields.

UIF

Bit 0: Update interrupt flag.

Allowed values:
0: Clear: No update occurred
1: UpdatePending: Update interrupt pending.

CC1IF

Bit 1: Capture/compare 1 interrupt flag.

CC2IF

Bit 2: Capture/Compare 2 interrupt flag.

CC3IF

Bit 3: Capture/Compare 3 interrupt flag.

CC4IF

Bit 4: Capture/Compare 4 interrupt flag.

TIF

Bit 6: Trigger interrupt flag.

Allowed values:
0: NoTrigger: No trigger event occurred
1: Trigger: Trigger interrupt pending

CC1OF

Bit 9: Capture/Compare 1 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC2OF

Bit 10: Capture/compare 2 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC3OF

Bit 11: Capture/Compare 3 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

CC4OF

Bit 12: Capture/Compare 4 overcapture flag.

Allowed values:
1: Overcapture: The counter value has been captured in TIMx_CCRx register while CCxIF flag was already set

EGR

event generation register

Offset: 0x14, reset: 0x0000, access: write-only

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									TG w		CC4G w	CC3G w	CC2G w	CC1G w	UG w

Toggle Fields.

UG

Bit 0: Update generation.

Allowed values:
1: Update: Re-initializes the timer counter and generates an update of the registers.

CC1G

Bit 1: Capture/compare 1 generation.

CC2G

Bit 2: Capture/compare 2 generation.

CC3G

Bit 3: Capture/compare 3 generation.

CC4G

Bit 4: Capture/compare 4 generation.

TG

Bit 6: Trigger generation.

Allowed values:
1: Trigger: The TIF flag is set in TIMx_SR register. Related interrupt or DMA transfer can occur if enabled.

CCMR1_Input

capture/compare mode register 1 (input mode)

Offset: 0x18, reset: 0x00000000, access: read-write

4/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC2F rw				IC2PSC rw		CC2S rw		IC1F rw				IC1PSC rw		CC1S rw

Toggle Fields.

CC1S

Bits 0-1: Capture/Compare 1 selection.

IC1PSC

Bits 2-3: Input capture 1 prescaler.

IC1F

Bits 4-7: Input capture 1 filter.

CC2S

Bits 8-9: Capture/compare 2 selection.

IC2PSC

Bits 10-11: Input capture 2 prescaler.

IC2F

Bits 12-15: Input capture 2 filter.

Allowed values: 0-15

CCMR2_Input

capture/compare mode register 2 (input mode)

Offset: 0x1C, reset: 0x00000000, access: read-write

6/6 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
IC4F rw				IC4PSC rw		CC4S rw		IC3F rw				IC3PSC rw		CC3S rw

Toggle Fields.

CC3S

Bits 0-1: Capture/Compare 3 selection.

IC3PSC

Bits 2-3: Input capture 3 prescaler.

Allowed values: 0-3

IC3F

Bits 4-7: Input capture 3 filter.

Allowed values: 0-15

CC4S

Bits 8-9: Capture/Compare 4 selection.

IC4PSC

Bits 10-11: Input capture 4 prescaler.

Allowed values: 0-3

IC4F

Bits 12-15: Input capture 4 filter.

Allowed values: 0-15

CCER

capture/compare enable register

Offset: 0x20, reset: 0x0000, access: read-write

0/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CC4NP rw		CC4P rw	CC4E rw	CC3NP rw		CC3P rw	CC3E rw	CC2NP rw		CC2P rw	CC2E rw	CC1NP rw		CC1P rw	CC1E rw

Toggle Fields.

CC1E

Bit 0: Capture/Compare 1 output enable.

CC1P

Bit 1: Capture/Compare 1 output Polarity.

CC1NP

Bit 3: Capture/Compare 1 output Polarity.

CC2E

Bit 4: Capture/Compare 2 output enable.

CC2P

Bit 5: Capture/Compare 2 output Polarity.

CC2NP

Bit 7: Capture/Compare 2 output Polarity.

CC3E

Bit 8: Capture/Compare 3 output enable.

CC3P

Bit 9: Capture/Compare 3 output Polarity.

CC3NP

Bit 11: Capture/Compare 3 output Polarity.

CC4E

Bit 12: Capture/Compare 4 output enable.

CC4P

Bit 13: Capture/Compare 3 output Polarity.

CC4NP

Bit 15: Capture/Compare 4 output Polarity.

CNT

counter

Offset: 0x24, reset: 0x00000000, access: read-write

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CNT_H rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CNT rw

Toggle Fields.

CNT

Bits 0-15: Counter value.

Allowed values: 0-65535

CNT_H

Bits 16-31: High counter value (TIM2 only).

PSC

prescaler

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
PSC rw

Toggle Fields.

PSC

Bits 0-15: Prescaler value.

Allowed values: 0-65535

ARR

auto-reload register

Offset: 0x2C, reset: 0x00000000, access: read-write

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ARR_H rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle Fields.

ARR

Bits 0-15: Auto-reload value.

Allowed values: 0-65535

ARR_H

Bits 16-31: High Auto-reload value (TIM2 only).

CCR%s

capture/compare register 1

Offset: 0x34, reset: 0x00000000, access: read-write

1/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CCR1_H rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CCR rw

Toggle Fields.

CCR

Bits 0-15: Capture/Compare 1 value.

Allowed values: 0-65535

CCR1_H

Bits 16-31: High Capture/Compare 1 value (TIM2 only).

DCR

DMA control register

Offset: 0x48, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			DBL rw								DBA rw

Toggle Fields.

DBA

Bits 0-4: DMA base address.

Allowed values: 0-31

DBL

Bits 8-12: DMA burst length.

Allowed values: 0-18

DMAR

DMA address for full transfer

Offset: 0x4C, reset: 0x0000, access: read-write

0/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DMAR rw

Toggle Fields.

DMAR

Bits 0-15: DMA register for burst accesses.

TIM6

0x40001000: Basic-timers

13/13 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									MMS rw

Toggle Fields.

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: Use UG bit from TIMx_EGR register
1: Enable: Use CNT bit from TIMx_CEN register
2: Update: Use the update event

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							UDE rw								UIE rw

Toggle Fields.

UIE

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle Fields.

ARR

Bits 0-15: Low Auto-reload value.

Allowed values: 0-65536

TIM7

0x40001400: Basic-timers

13/13 fields covered. Toggle Registers.

CR1

control register 1

Offset: 0x0, reset: 0x0000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								ARPE rw				OPM rw	URS rw	UDIS rw	CEN rw

Toggle Fields.

CEN

Bit 0: Counter enable.

Allowed values:
0: Disabled: Counter disabled
1: Enabled: Counter enabled

UDIS

Bit 1: Update disable.

Allowed values:
0: Enabled: Update event enabled
1: Disabled: Update event disabled

URS

Bit 2: Update request source.

OPM

Bit 3: One-pulse mode.

Allowed values:
0: Disabled: Counter is not stopped at update event
1: Enabled: Counter stops counting at the next update event (clearing the CEN bit)

ARPE

Bit 7: Auto-reload preload enable.

Allowed values:
0: Disabled: TIMx_APRR register is not buffered
1: Enabled: TIMx_APRR register is buffered

CR2

control register 2

Offset: 0x4, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
									MMS rw

Toggle Fields.

MMS

Bits 4-6: Master mode selection.

Allowed values:
0: Reset: Use UG bit from TIMx_EGR register
1: Enable: Use CNT bit from TIMx_CEN register
2: Update: Use the update event

DIER

DMA/Interrupt enable register

Offset: 0xC, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							UDE rw								UIE rw

Toggle Fields.

UIE

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ARR rw

Toggle Fields.

ARR

Bits 0-15: Low Auto-reload value.

Allowed values: 0-65536

TSC

0x40024000: Touch sensing controller

7/131 fields covered. Toggle Registers.

CR

control register

Offset: 0x0, reset: 0x00000000, access: read-write

0/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
CTPH rw				CTPL rw				SSD rw							SSE rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SSPSC rw	PGPSC rw							MCV rw			IODEF rw	SYNCPOL rw	AM rw	START rw	TSCE rw

Toggle Fields.

TSCE

Bit 0: Touch sensing controller enable.

START

Bit 1: Start a new acquisition.

AM

Bit 2: Acquisition mode.

SYNCPOL

Bit 3: Synchronization pin polarity.

IODEF

Bit 4: I/O Default mode.

MCV

Bits 5-7: Max count value.

PGPSC

Bits 12-14: pulse generator prescaler.

SSPSC

Bit 15: Spread spectrum prescaler.

SSE

Bit 16: Spread spectrum enable.

SSD

Bits 17-23: Spread spectrum deviation.

CTPL

Bits 24-27: Charge transfer pulse low.

CTPH

Bits 28-31: Charge transfer pulse high.

IER

interrupt enable register

Offset: 0x4, reset: 0x00000000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														MCEIE rw	EOAIE rw

Toggle Fields.

EOAIE

Bit 0: End of acquisition interrupt enable.

MCEIE

Bit 1: Max count error interrupt enable.

ICR

interrupt clear register

Offset: 0x8, reset: 0x00000000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														MCEIC rw	EOAIC rw

Toggle Fields.

EOAIC

Bit 0: End of acquisition interrupt clear.

MCEIC

Bit 1: Max count error interrupt clear.

ISR

interrupt status register

Offset: 0xC, reset: 0x00000000, access: read-write

0/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
														MCEF rw	EOAF rw

Toggle Fields.

EOAF

Bit 0: End of acquisition flag.

MCEF

Bit 1: Max count error flag.

IOHCR

I/O hysteresis control register

Offset: 0x10, reset: 0xFFFFFFFF, access: read-write

0/24 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								G6_IO4 rw	G6_IO3 rw	G6_IO2 rw	G6_IO1 rw	G5_IO4 rw	G5_IO3 rw	G5_IO2 rw	G5_IO1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
G4_IO4 rw	G4_IO3 rw	G4_IO2 rw	G4_IO1 rw	G3_IO4 rw	G3_IO3 rw	G3_IO2 rw	G3_IO1 rw	G2_IO4 rw	G2_IO3 rw	G2_IO2 rw	G2_IO1 rw	G1_IO4 rw	G1_IO3 rw	G1_IO2 rw	G1_IO1 rw

Toggle Fields.

G1_IO1

Bit 0: G1_IO1 Schmitt trigger hysteresis mode.

G1_IO2

Bit 1: G1_IO2 Schmitt trigger hysteresis mode.

G1_IO3

Bit 2: G1_IO3 Schmitt trigger hysteresis mode.

G1_IO4

Bit 3: G1_IO4 Schmitt trigger hysteresis mode.

G2_IO1

Bit 4: G2_IO1 Schmitt trigger hysteresis mode.

G2_IO2

Bit 5: G2_IO2 Schmitt trigger hysteresis mode.

G2_IO3

Bit 6: G2_IO3 Schmitt trigger hysteresis mode.

G2_IO4

Bit 7: G2_IO4 Schmitt trigger hysteresis mode.

G3_IO1

Bit 8: G3_IO1 Schmitt trigger hysteresis mode.

G3_IO2

Bit 9: G3_IO2 Schmitt trigger hysteresis mode.

G3_IO3

Bit 10: G3_IO3 Schmitt trigger hysteresis mode.

G3_IO4

Bit 11: G3_IO4 Schmitt trigger hysteresis mode.

G4_IO1

Bit 12: G4_IO1 Schmitt trigger hysteresis mode.

G4_IO2

Bit 13: G4_IO2 Schmitt trigger hysteresis mode.

G4_IO3

Bit 14: G4_IO3 Schmitt trigger hysteresis mode.

G4_IO4

Bit 15: G4_IO4 Schmitt trigger hysteresis mode.

G5_IO1

Bit 16: G5_IO1 Schmitt trigger hysteresis mode.

G5_IO2

Bit 17: G5_IO2 Schmitt trigger hysteresis mode.

G5_IO3

Bit 18: G5_IO3 Schmitt trigger hysteresis mode.

G5_IO4

Bit 19: G5_IO4 Schmitt trigger hysteresis mode.

G6_IO1

Bit 20: G6_IO1 Schmitt trigger hysteresis mode.

G6_IO2

Bit 21: G6_IO2 Schmitt trigger hysteresis mode.

G6_IO3

Bit 22: G6_IO3 Schmitt trigger hysteresis mode.

G6_IO4

Bit 23: G6_IO4 Schmitt trigger hysteresis mode.

IOASCR

I/O analog switch control register

Offset: 0x18, reset: 0x00000000, access: read-write

0/24 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								G6_IO4 rw	G6_IO3 rw	G6_IO2 rw	G6_IO1 rw	G5_IO4 rw	G5_IO3 rw	G5_IO2 rw	G5_IO1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
G4_IO4 rw	G4_IO3 rw	G4_IO2 rw	G4_IO1 rw	G3_IO4 rw	G3_IO3 rw	G3_IO2 rw	G3_IO1 rw	G2_IO4 rw	G2_IO3 rw	G2_IO2 rw	G2_IO1 rw	G1_IO4 rw	G1_IO3 rw	G1_IO2 rw	G1_IO1 rw

Toggle Fields.

G1_IO1

Bit 0: G1_IO1 analog switch enable.

G1_IO2

Bit 1: G1_IO2 analog switch enable.

G1_IO3

Bit 2: G1_IO3 analog switch enable.

G1_IO4

Bit 3: G1_IO4 analog switch enable.

G2_IO1

Bit 4: G2_IO1 analog switch enable.

G2_IO2

Bit 5: G2_IO2 analog switch enable.

G2_IO3

Bit 6: G2_IO3 analog switch enable.

G2_IO4

Bit 7: G2_IO4 analog switch enable.

G3_IO1

Bit 8: G3_IO1 analog switch enable.

G3_IO2

Bit 9: G3_IO2 analog switch enable.

G3_IO3

Bit 10: G3_IO3 analog switch enable.

G3_IO4

Bit 11: G3_IO4 analog switch enable.

G4_IO1

Bit 12: G4_IO1 analog switch enable.

G4_IO2

Bit 13: G4_IO2 analog switch enable.

G4_IO3

Bit 14: G4_IO3 analog switch enable.

G4_IO4

Bit 15: G4_IO4 analog switch enable.

G5_IO1

Bit 16: G5_IO1 analog switch enable.

G5_IO2

Bit 17: G5_IO2 analog switch enable.

G5_IO3

Bit 18: G5_IO3 analog switch enable.

G5_IO4

Bit 19: G5_IO4 analog switch enable.

G6_IO1

Bit 20: G6_IO1 analog switch enable.

G6_IO2

Bit 21: G6_IO2 analog switch enable.

G6_IO3

Bit 22: G6_IO3 analog switch enable.

G6_IO4

Bit 23: G6_IO4 analog switch enable.

IOSCR

I/O sampling control register

Offset: 0x20, reset: 0x00000000, access: read-write

0/24 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								G6_IO4 rw	G6_IO3 rw	G6_IO2 rw	G6_IO1 rw	G5_IO4 rw	G5_IO3 rw	G5_IO2 rw	G5_IO1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
G4_IO4 rw	G4_IO3 rw	G4_IO2 rw	G4_IO1 rw	G3_IO4 rw	G3_IO3 rw	G3_IO2 rw	G3_IO1 rw	G2_IO4 rw	G2_IO3 rw	G2_IO2 rw	G2_IO1 rw	G1_IO4 rw	G1_IO3 rw	G1_IO2 rw	G1_IO1 rw

Toggle Fields.

G1_IO1

Bit 0: G1_IO1 sampling mode.

G1_IO2

Bit 1: G1_IO2 sampling mode.

G1_IO3

Bit 2: G1_IO3 sampling mode.

G1_IO4

Bit 3: G1_IO4 sampling mode.

G2_IO1

Bit 4: G2_IO1 sampling mode.

G2_IO2

Bit 5: G2_IO2 sampling mode.

G2_IO3

Bit 6: G2_IO3 sampling mode.

G2_IO4

Bit 7: G2_IO4 sampling mode.

G3_IO1

Bit 8: G3_IO1 sampling mode.

G3_IO2

Bit 9: G3_IO2 sampling mode.

G3_IO3

Bit 10: G3_IO3 sampling mode.

G3_IO4

Bit 11: G3_IO4 sampling mode.

G4_IO1

Bit 12: G4_IO1 sampling mode.

G4_IO2

Bit 13: G4_IO2 sampling mode.

G4_IO3

Bit 14: G4_IO3 sampling mode.

G4_IO4

Bit 15: G4_IO4 sampling mode.

G5_IO1

Bit 16: G5_IO1 sampling mode.

G5_IO2

Bit 17: G5_IO2 sampling mode.

G5_IO3

Bit 18: G5_IO3 sampling mode.

G5_IO4

Bit 19: G5_IO4 sampling mode.

G6_IO1

Bit 20: G6_IO1 sampling mode.

G6_IO2

Bit 21: G6_IO2 sampling mode.

G6_IO3

Bit 22: G6_IO3 sampling mode.

G6_IO4

Bit 23: G6_IO4 sampling mode.

IOCCR

I/O channel control register

Offset: 0x28, reset: 0x00000000, access: read-write

0/24 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								G6_IO4 rw	G6_IO3 rw	G6_IO2 rw	G6_IO1 rw	G5_IO4 rw	G5_IO3 rw	G5_IO2 rw	G5_IO1 rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
G4_IO4 rw	G4_IO3 rw	G4_IO2 rw	G4_IO1 rw	G3_IO4 rw	G3_IO3 rw	G3_IO2 rw	G3_IO1 rw	G2_IO4 rw	G2_IO3 rw	G2_IO2 rw	G2_IO1 rw	G1_IO4 rw	G1_IO3 rw	G1_IO2 rw	G1_IO1 rw

Toggle Fields.

G1_IO1

Bit 0: G1_IO1 channel mode.

G1_IO2

Bit 1: G1_IO2 channel mode.

G1_IO3

Bit 2: G1_IO3 channel mode.

G1_IO4

Bit 3: G1_IO4 channel mode.

G2_IO1

Bit 4: G2_IO1 channel mode.

G2_IO2

Bit 5: G2_IO2 channel mode.

G2_IO3

Bit 6: G2_IO3 channel mode.

G2_IO4

Bit 7: G2_IO4 channel mode.

G3_IO1

Bit 8: G3_IO1 channel mode.

G3_IO2

Bit 9: G3_IO2 channel mode.

G3_IO3

Bit 10: G3_IO3 channel mode.

G3_IO4

Bit 11: G3_IO4 channel mode.

G4_IO1

Bit 12: G4_IO1 channel mode.

G4_IO2

Bit 13: G4_IO2 channel mode.

G4_IO3

Bit 14: G4_IO3 channel mode.

G4_IO4

Bit 15: G4_IO4 channel mode.

G5_IO1

Bit 16: G5_IO1 channel mode.

G5_IO2

Bit 17: G5_IO2 channel mode.

G5_IO3

Bit 18: G5_IO3 channel mode.

G5_IO4

Bit 19: G5_IO4 channel mode.

G6_IO1

Bit 20: G6_IO1 channel mode.

G6_IO2

Bit 21: G6_IO2 channel mode.

G6_IO3

Bit 22: G6_IO3 channel mode.

G6_IO4

Bit 23: G6_IO4 channel mode.

IOGCSR

I/O group control status register

Offset: 0x30, reset: 0x00000000, access: Unspecified

6/16 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
								G8S rw	G7S rw	G6S r	G5S r	G4S r	G3S r	G2S r	G1S r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								G8E rw	G7E rw	G6E rw	G5E rw	G4E rw	G3E rw	G2E rw	G1E rw

Toggle Fields.

G1E

Bit 0: Analog I/O group x enable.

G2E

Bit 1: Analog I/O group x enable.

G3E

Bit 2: Analog I/O group x enable.

G4E

Bit 3: Analog I/O group x enable.

G5E

Bit 4: Analog I/O group x enable.

G6E

Bit 5: Analog I/O group x enable.

G7E

Bit 6: Analog I/O group x enable.

G8E

Bit 7: Analog I/O group x enable.

G1S

Bit 16: Analog I/O group x status.

G2S

Bit 17: Analog I/O group x status.

G3S

Bit 18: Analog I/O group x status.

G4S

Bit 19: Analog I/O group x status.

G5S

Bit 20: Analog I/O group x status.

G6S

Bit 21: Analog I/O group x status.

G7S

Bit 22: Analog I/O group x status.

G8S

Bit 23: Analog I/O group x status.

IOG%sCR

I/O group x counter register

Offset: 0x34, reset: 0x00000000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
		CNT r

Toggle Fields.

CNT

Bits 0-13: Counter value.

USART1

0x40013800: Universal synchronous asynchronous receiver transmitter

104/104 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x0000, access: read-write

21/21 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			M1 rw	EOBIE rw	RTOIE rw	DEAT rw					DEDT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OVER8 rw	CMIE rw	MME rw	M0 rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle Fields.

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M0

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0-31

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0-31

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

M1

Bit 28: Word length.

Allowed values:
0: M0: Use M0 to set the data bits
1: Bit7: 1 start bit, 7 data bits, n stop bits

CR2

Control register 2

Offset: 0x4, reset: 0x0000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD rw								RTOEN rw	ABRMOD rw		ABREN rw	MSBFIRST rw	DATAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw	LINEN rw	STOP rw		CLKEN rw	CPOL rw	CPHA rw	LBCL rw		LBDIE rw	LBDL rw	ADDM7 rw

Toggle Fields.

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

Allowed values:
0: Positive: Logical data from the data register are send/received in positive/direct logic
1: Negative: Logical data from the data register are send/received in negative/inverse logic

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

Allowed values:
0: Start: Measurement of the start bit is used to detect the baud rate
1: Edge: Falling edge to falling edge measurement
2: Frame7F: 0x7F frame detection
3: Frame55: 0x55 frame detection

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0-255

CR3

Control register 3

Offset: 0x8, reset: 0x0000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									WUFIE rw	WUS rw		SCARCNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw	ONEBIT rw	CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw	SCEN rw	NACK rw	HDSEL rw	IRLP rw	IREN rw	EIE rw

Toggle Fields.

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

Allowed values:
0: Enabled: Overrun Error Flag, ORE, is set when received data is not read before receiving new data
1: Disabled: Overrun functionality is disabled. If new data is received while the RXNE flag is still set the ORE flag is not set and the new received data overwrites the previous content of the RDR register

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0-7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle Fields.

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0-65535

GTPR

Guard time and prescaler register

Offset: 0x10, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
GT rw								PSC rw

Toggle Fields.

PSC

Bits 0-7: Prescaler value.

Allowed values: 0-255

GT

Bits 8-15: Guard time value.

Allowed values: 0-255

RTOR

Receiver timeout register

Offset: 0x14, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BLEN rw								RTO rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTO rw

Toggle Fields.

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0-16777215

BLEN

Bits 24-31: Block Length.

Allowed values: 0-255

RQR

Request register

Offset: 0x18, reset: 0x0000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ rw	RXFRQ rw	MMRQ rw	SBKRQ rw	ABRRQ rw

Toggle Fields.

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1C, reset: 0x00C0, access: read-only

22/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRF r	ABRE r		EOBF r	RTOF r	CTS r	CTSIF r	LBDF r	TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle Fields.

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, reset: 0x0000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF rw			CMCF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			EOBCF rw	RTOCF rw		CTSCF rw	LBDCF rw		TCCF rw		IDLECF rw	ORECF rw	NCF rw	FECF rw	PECF rw

Toggle Fields.

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, reset: 0x0000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle Fields.

RDR

Bits 0-8: Receive data value.

Allowed values: 0-255

TDR

Transmit data register

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle Fields.

TDR

Bits 0-8: Transmit data value.

Allowed values: 0-255

USART2

0x40004400: Universal synchronous asynchronous receiver transmitter

104/104 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x0000, access: read-write

21/21 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			M1 rw	EOBIE rw	RTOIE rw	DEAT rw					DEDT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OVER8 rw	CMIE rw	MME rw	M0 rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle Fields.

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M0

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0-31

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0-31

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

M1

Bit 28: Word length.

Allowed values:
0: M0: Use M0 to set the data bits
1: Bit7: 1 start bit, 7 data bits, n stop bits

CR2

Control register 2

Offset: 0x4, reset: 0x0000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD rw								RTOEN rw	ABRMOD rw		ABREN rw	MSBFIRST rw	DATAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw	LINEN rw	STOP rw		CLKEN rw	CPOL rw	CPHA rw	LBCL rw		LBDIE rw	LBDL rw	ADDM7 rw

Toggle Fields.

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0-255

CR3

Control register 3

Offset: 0x8, reset: 0x0000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									WUFIE rw	WUS rw		SCARCNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw	ONEBIT rw	CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw	SCEN rw	NACK rw	HDSEL rw	IRLP rw	IREN rw	EIE rw

Toggle Fields.

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0-7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle Fields.

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0-65535

GTPR

Guard time and prescaler register

Offset: 0x10, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
GT rw								PSC rw

Toggle Fields.

PSC

Bits 0-7: Prescaler value.

Allowed values: 0-255

GT

Bits 8-15: Guard time value.

Allowed values: 0-255

RTOR

Receiver timeout register

Offset: 0x14, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BLEN rw								RTO rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTO rw

Toggle Fields.

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0-16777215

BLEN

Bits 24-31: Block Length.

Allowed values: 0-255

RQR

Request register

Offset: 0x18, reset: 0x0000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ rw	RXFRQ rw	MMRQ rw	SBKRQ rw	ABRRQ rw

Toggle Fields.

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1C, reset: 0x00C0, access: read-only

22/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRF r	ABRE r		EOBF r	RTOF r	CTS r	CTSIF r	LBDF r	TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle Fields.

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, reset: 0x0000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF rw			CMCF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			EOBCF rw	RTOCF rw		CTSCF rw	LBDCF rw		TCCF rw		IDLECF rw	ORECF rw	NCF rw	FECF rw	PECF rw

Toggle Fields.

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, reset: 0x0000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle Fields.

RDR

Bits 0-8: Receive data value.

Allowed values: 0-255

TDR

Transmit data register

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle Fields.

TDR

Bits 0-8: Transmit data value.

Allowed values: 0-255

USART3

0x40004800: Universal synchronous asynchronous receiver transmitter

104/104 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x0000, access: read-write

21/21 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			M1 rw	EOBIE rw	RTOIE rw	DEAT rw					DEDT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OVER8 rw	CMIE rw	MME rw	M0 rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle Fields.

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M0

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0-31

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0-31

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

M1

Bit 28: Word length.

Allowed values:
0: M0: Use M0 to set the data bits
1: Bit7: 1 start bit, 7 data bits, n stop bits

CR2

Control register 2

Offset: 0x4, reset: 0x0000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD rw								RTOEN rw	ABRMOD rw		ABREN rw	MSBFIRST rw	DATAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw	LINEN rw	STOP rw		CLKEN rw	CPOL rw	CPHA rw	LBCL rw		LBDIE rw	LBDL rw	ADDM7 rw

Toggle Fields.

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0-255

CR3

Control register 3

Offset: 0x8, reset: 0x0000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									WUFIE rw	WUS rw		SCARCNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw	ONEBIT rw	CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw	SCEN rw	NACK rw	HDSEL rw	IRLP rw	IREN rw	EIE rw

Toggle Fields.

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0-7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle Fields.

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0-65535

GTPR

Guard time and prescaler register

Offset: 0x10, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
GT rw								PSC rw

Toggle Fields.

PSC

Bits 0-7: Prescaler value.

Allowed values: 0-255

GT

Bits 8-15: Guard time value.

Allowed values: 0-255

RTOR

Receiver timeout register

Offset: 0x14, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BLEN rw								RTO rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTO rw

Toggle Fields.

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0-16777215

BLEN

Bits 24-31: Block Length.

Allowed values: 0-255

RQR

Request register

Offset: 0x18, reset: 0x0000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ rw	RXFRQ rw	MMRQ rw	SBKRQ rw	ABRRQ rw

Toggle Fields.

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1C, reset: 0x00C0, access: read-only

22/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRF r	ABRE r		EOBF r	RTOF r	CTS r	CTSIF r	LBDF r	TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle Fields.

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, reset: 0x0000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF rw			CMCF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			EOBCF rw	RTOCF rw		CTSCF rw	LBDCF rw		TCCF rw		IDLECF rw	ORECF rw	NCF rw	FECF rw	PECF rw

Toggle Fields.

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, reset: 0x0000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle Fields.

RDR

Bits 0-8: Receive data value.

Allowed values: 0-255

TDR

Transmit data register

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle Fields.

TDR

Bits 0-8: Transmit data value.

Allowed values: 0-255

USART4

0x40004C00: Universal synchronous asynchronous receiver transmitter

104/104 fields covered. Toggle Registers.

CR1

Control register 1

Offset: 0x0, reset: 0x0000, access: read-write

21/21 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
			M1 rw	EOBIE rw	RTOIE rw	DEAT rw					DEDT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
OVER8 rw	CMIE rw	MME rw	M0 rw	WAKE rw	PCE rw	PS rw	PEIE rw	TXEIE rw	TCIE rw	RXNEIE rw	IDLEIE rw	TE rw	RE rw	UESM rw	UE rw

Toggle Fields.

UE

Bit 0: USART enable.

Allowed values:
0: Disabled: UART is disabled
1: Enabled: UART is enabled

UESM

Bit 1: USART enable in Stop mode.

Allowed values:
0: Disabled: USART not able to wake up the MCU from Stop mode
1: Enabled: USART able to wake up the MCU from Stop mode

RE

Bit 2: Receiver enable.

Allowed values:
0: Disabled: Receiver is disabled
1: Enabled: Receiver is enabled

TE

Bit 3: Transmitter enable.

Allowed values:
0: Disabled: Transmitter is disabled
1: Enabled: Transmitter is enabled

IDLEIE

Bit 4: IDLE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever IDLE=1 in the ISR register

RXNEIE

Bit 5: RXNE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever ORE=1 or RXNE=1 in the ISR register

TCIE

Bit 6: Transmission complete interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TC=1 in the ISR register

TXEIE

Bit 7: interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever TXE=1 in the ISR register

PEIE

Bit 8: PE interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated whenever PE=1 in the ISR register

PS

Bit 9: Parity selection.

Allowed values:
0: Even: Even parity
1: Odd: Odd parity

PCE

Bit 10: Parity control enable.

Allowed values:
0: Disabled: Parity control disabled
1: Enabled: Parity control enabled

WAKE

Bit 11: Receiver wakeup method.

Allowed values:
0: Idle: Idle line
1: Address: Address mask

M0

Bit 12: Word length.

Allowed values:
0: Bit8: 1 start bit, 8 data bits, n stop bits
1: Bit9: 1 start bit, 9 data bits, n stop bits

MME

Bit 13: Mute mode enable.

Allowed values:
0: Disabled: Receiver in active mode permanently
1: Enabled: Receiver can switch between mute mode and active mode

CMIE

Bit 14: Character match interrupt enable.

Allowed values:
0: Disabled: Interrupt is disabled
1: Enabled: Interrupt is generated when the CMF bit is set in the ISR register

OVER8

Bit 15: Oversampling mode.

Allowed values:
0: Oversampling16: Oversampling by 16
1: Oversampling8: Oversampling by 8

DEDT

Bits 16-20: Driver Enable deassertion time.

Allowed values: 0-31

DEAT

Bits 21-25: Driver Enable assertion time.

Allowed values: 0-31

RTOIE

Bit 26: Receiver timeout interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated when the RTOF bit is set in the ISR register

EOBIE

Bit 27: End of Block interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: A USART interrupt is generated when the EOBF flag is set in the ISR register

M1

Bit 28: Word length.

Allowed values:
0: M0: Use M0 to set the data bits
1: Bit7: 1 start bit, 7 data bits, n stop bits

CR2

Control register 2

Offset: 0x4, reset: 0x0000, access: read-write

18/18 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
ADD rw								RTOEN rw	ABRMOD rw		ABREN rw	MSBFIRST rw	DATAINV rw	TXINV rw	RXINV rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
SWAP rw	LINEN rw	STOP rw		CLKEN rw	CPOL rw	CPHA rw	LBCL rw		LBDIE rw	LBDL rw	ADDM7 rw

Toggle Fields.

ADDM7

Bit 4: 7-bit Address Detection/4-bit Address Detection.

Allowed values:
0: Bit4: 4-bit address detection
1: Bit7: 7-bit address detection

LBDL

Bit 5: LIN break detection length.

Allowed values:
0: Bit10: 10-bit break detection
1: Bit11: 11-bit break detection

LBDIE

Bit 6: LIN break detection interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever LBDF=1 in the ISR register

LBCL

Bit 8: Last bit clock pulse.

Allowed values:
0: NotOutput: The clock pulse of the last data bit is not output to the CK pin
1: Output: The clock pulse of the last data bit is output to the CK pin

CPHA

Bit 9: Clock phase.

Allowed values:
0: First: The first clock transition is the first data capture edge
1: Second: The second clock transition is the first data capture edge

CPOL

Bit 10: Clock polarity.

Allowed values:
0: Low: Steady low value on CK pin outside transmission window
1: High: Steady high value on CK pin outside transmission window

CLKEN

Bit 11: Clock enable.

Allowed values:
0: Disabled: CK pin disabled
1: Enabled: CK pin enabled

STOP

Bits 12-13: STOP bits.

Allowed values:
0: Stop1: 1 stop bit
1: Stop0p5: 0.5 stop bit
2: Stop2: 2 stop bit
3: Stop1p5: 1.5 stop bit

LINEN

Bit 14: LIN mode enable.

Allowed values:
0: Disabled: LIN mode disabled
1: Enabled: LIN mode enabled

SWAP

Bit 15: Swap TX/RX pins.

Allowed values:
0: Standard: TX/RX pins are used as defined in standard pinout
1: Swapped: The TX and RX pins functions are swapped

RXINV

Bit 16: RX pin active level inversion.

Allowed values:
0: Standard: RX pin signal works using the standard logic levels
1: Inverted: RX pin signal values are inverted

TXINV

Bit 17: TX pin active level inversion.

Allowed values:
0: Standard: TX pin signal works using the standard logic levels
1: Inverted: TX pin signal values are inverted

DATAINV

Bit 18: Binary data inversion.

MSBFIRST

Bit 19: Most significant bit first.

Allowed values:
0: LSB: data is transmitted/received with data bit 0 first, following the start bit
1: MSB: data is transmitted/received with MSB (bit 7/8/9) first, following the start bit

ABREN

Bit 20: Auto baud rate enable.

Allowed values:
0: Disabled: Auto baud rate detection is disabled
1: Enabled: Auto baud rate detection is enabled

ABRMOD

Bits 21-22: Auto baud rate mode.

RTOEN

Bit 23: Receiver timeout enable.

Allowed values:
0: Disabled: Receiver timeout feature disabled
1: Enabled: Receiver timeout feature enabled

ADD

Bits 24-31: Address of the USART node.

Allowed values: 0-255

CR3

Control register 3

Offset: 0x8, reset: 0x0000, access: read-write

19/19 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									WUFIE rw	WUS rw		SCARCNT rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DEP rw	DEM rw	DDRE rw	OVRDIS rw	ONEBIT rw	CTSIE rw	CTSE rw	RTSE rw	DMAT rw	DMAR rw	SCEN rw	NACK rw	HDSEL rw	IRLP rw	IREN rw	EIE rw

Toggle Fields.

EIE

Bit 0: Error interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the ISR register

IREN

Bit 1: IrDA mode enable.

Allowed values:
0: Disabled: IrDA disabled
1: Enabled: IrDA enabled

IRLP

Bit 2: IrDA low-power.

Allowed values:
0: Normal: Normal mode
1: LowPower: Low-power mode

HDSEL

Bit 3: Half-duplex selection.

Allowed values:
0: NotSelected: Half duplex mode is not selected
1: Selected: Half duplex mode is selected

NACK

Bit 4: Smartcard NACK enable.

Allowed values:
0: Disabled: NACK transmission in case of parity error is disabled
1: Enabled: NACK transmission during parity error is enabled

SCEN

Bit 5: Smartcard mode enable.

Allowed values:
0: Disabled: Smartcard Mode disabled
1: Enabled: Smartcard Mode enabled

DMAR

Bit 6: DMA enable receiver.

Allowed values:
0: Disabled: DMA mode is disabled for reception
1: Enabled: DMA mode is enabled for reception

DMAT

Bit 7: DMA enable transmitter.

Allowed values:
0: Disabled: DMA mode is disabled for transmission
1: Enabled: DMA mode is enabled for transmission

RTSE

Bit 8: RTS enable.

Allowed values:
0: Disabled: RTS hardware flow control disabled
1: Enabled: RTS output enabled, data is only requested when there is space in the receive buffer

CTSE

Bit 9: CTS enable.

Allowed values:
0: Disabled: CTS hardware flow control disabled
1: Enabled: CTS mode enabled, data is only transmitted when the CTS input is asserted

CTSIE

Bit 10: CTS interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An interrupt is generated whenever CTSIF=1 in the ISR register

ONEBIT

Bit 11: One sample bit method enable.

Allowed values:
0: Sample3: Three sample bit method
1: Sample1: One sample bit method

OVRDIS

Bit 12: Overrun Disable.

DDRE

Bit 13: DMA Disable on Reception Error.

Allowed values:
0: NotDisabled: DMA is not disabled in case of reception error
1: Disabled: DMA is disabled following a reception error

DEM

Bit 14: Driver enable mode.

Allowed values:
0: Disabled: DE function is disabled
1: Enabled: The DE signal is output on the RTS pin

DEP

Bit 15: Driver enable polarity selection.

Allowed values:
0: High: DE signal is active high
1: Low: DE signal is active low

SCARCNT

Bits 17-19: Smartcard auto-retry count.

Allowed values: 0-7

WUS

Bits 20-21: Wakeup from Stop mode interrupt flag selection.

Allowed values:
0: Address: WUF active on address match
2: Start: WuF active on Start bit detection
3: RXNE: WUF active on RXNE

WUFIE

Bit 22: Wakeup from Stop mode interrupt enable.

Allowed values:
0: Disabled: Interrupt is inhibited
1: Enabled: An USART interrupt is generated whenever WUF=1 in the ISR register

BRR

Baud rate register

Offset: 0xC, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BRR rw

Toggle Fields.

BRR

Bits 0-15: mantissa of USARTDIV.

Allowed values: 0-65535

GTPR

Guard time and prescaler register

Offset: 0x10, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
GT rw								PSC rw

Toggle Fields.

PSC

Bits 0-7: Prescaler value.

Allowed values: 0-255

GT

Bits 8-15: Guard time value.

Allowed values: 0-255

RTOR

Receiver timeout register

Offset: 0x14, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
BLEN rw								RTO rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RTO rw

Toggle Fields.

RTO

Bits 0-23: Receiver timeout value.

Allowed values: 0-16777215

BLEN

Bits 24-31: Block Length.

Allowed values: 0-255

RQR

Request register

Offset: 0x18, reset: 0x0000, access: read-write

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
											TXFRQ rw	RXFRQ rw	MMRQ rw	SBKRQ rw	ABRRQ rw

Toggle Fields.

ABRRQ

Bit 0: Auto baud rate request.

Allowed values:
1: Request: resets the ABRF flag in the USART_ISR and request an automatic baud rate measurement on the next received data frame

SBKRQ

Bit 1: Send break request.

Allowed values:
1: Break: sets the SBKF flag and request to send a BREAK on the line, as soon as the transmit machine is available

MMRQ

Bit 2: Mute mode request.

Allowed values:
1: Mute: Puts the USART in mute mode and sets the RWU flag

RXFRQ

Bit 3: Receive data flush request.

Allowed values:
1: Discard: clears the RXNE flag. This allows to discard the received data without reading it, and avoid an overrun condition

TXFRQ

Bit 4: Transmit data flush request.

Allowed values:
1: Discard: Set the TXE flags. This allows to discard the transmit data

ISR

Interrupt & status register

Offset: 0x1C, reset: 0x00C0, access: read-only

22/22 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
									REACK r	TEACK r	WUF r	RWU r	SBKF r	CMF r	BUSY r
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
ABRF r	ABRE r		EOBF r	RTOF r	CTS r	CTSIF r	LBDF r	TXE r	TC r	RXNE r	IDLE r	ORE r	NF r	FE r	PE r

Toggle Fields.

PE

Bit 0: Parity error.

FE

Bit 1: Framing error.

NF

Bit 2: Noise detected flag.

ORE

Bit 3: Overrun error.

IDLE

Bit 4: Idle line detected.

RXNE

Bit 5: Read data register not empty.

TC

Bit 6: Transmission complete.

TXE

Bit 7: Transmit data register empty.

LBDF

Bit 8: LIN break detection flag.

CTSIF

Bit 9: CTS interrupt flag.

CTS

Bit 10: CTS flag.

RTOF

Bit 11: Receiver timeout.

EOBF

Bit 12: End of block flag.

ABRE

Bit 14: Auto baud rate error.

ABRF

Bit 15: Auto baud rate flag.

BUSY

Bit 16: Busy flag.

CMF

Bit 17: character match flag.

SBKF

Bit 18: Send break flag.

RWU

Bit 19: Receiver wakeup from Mute mode.

WUF

Bit 20: Wakeup from Stop mode flag.

TEACK

Bit 21: Transmit enable acknowledge flag.

REACK

Bit 22: Receive enable acknowledge flag.

ICR

Interrupt flag clear register

Offset: 0x20, reset: 0x0000, access: read-write

12/12 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16
											WUCF rw			CMCF rw
15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
			EOBCF rw	RTOCF rw		CTSCF rw	LBDCF rw		TCCF rw		IDLECF rw	ORECF rw	NCF rw	FECF rw	PECF rw

Toggle Fields.

PECF

Bit 0: Parity error clear flag.

Allowed values:
1: Clear: Clears the PE flag in the ISR register

FECF

Bit 1: Framing error clear flag.

Allowed values:
1: Clear: Clears the FE flag in the ISR register

NCF

Bit 2: Noise detected clear flag.

Allowed values:
1: Clear: Clears the NF flag in the ISR register

ORECF

Bit 3: Overrun error clear flag.

Allowed values:
1: Clear: Clears the ORE flag in the ISR register

IDLECF

Bit 4: Idle line detected clear flag.

Allowed values:
1: Clear: Clears the IDLE flag in the ISR register

TCCF

Bit 6: Transmission complete clear flag.

Allowed values:
1: Clear: Clears the TC flag in the ISR register

LBDCF

Bit 8: LIN break detection clear flag.

Allowed values:
1: Clear: Clears the LBDF flag in the ISR register

CTSCF

Bit 9: CTS clear flag.

Allowed values:
1: Clear: Clears the CTSIF flag in the ISR register

RTOCF

Bit 11: Receiver timeout clear flag.

Allowed values:
1: Clear: Clears the RTOF flag in the ISR register

EOBCF

Bit 12: End of timeout clear flag.

Allowed values:
1: Clear: Clears the EOBF flag in the ISR register

CMCF

Bit 17: Character match clear flag.

Allowed values:
1: Clear: Clears the CMF flag in the ISR register

WUCF

Bit 20: Wakeup from Stop mode clear flag.

Allowed values:
1: Clear: Clears the WUF flag in the ISR register

RDR

Receive data register

Offset: 0x24, reset: 0x0000, access: read-only

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							RDR r

Toggle Fields.

RDR

Bits 0-8: Receive data value.

Allowed values: 0-255

TDR

Transmit data register

Offset: 0x28, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
							TDR rw

Toggle Fields.

TDR

Bits 0-8: Transmit data value.

Allowed values: 0-255

USB

0x40005C00: Universal serial bus full-speed device interface

51/57 fields covered. Toggle Registers.

EP%sR

endpoint 0 register

Offset: 0x0, reset: 0x00000000, access: read-write

4/10 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTR_RX rw	DTOG_RX rw	STAT_RX rw		SETUP rw	EP_TYPE rw		EP_KIND rw	CTR_TX rw	DTOG_TX rw	STAT_TX rw		EA rw

Toggle Fields.

EA

Bits 0-3: Endpoint address.

Allowed values: 0-15

STAT_TX

Bits 4-5: Status bits, for transmission transfers.

Allowed values:
0: Disabled: all transmission requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all transmission requests result in a STALL handshake
2: Nak: the endpoint is naked and all transmission requests result in a NAK handshake
3: Valid: this endpoint is enabled for transmission

DTOG_TX

Bit 6: Data Toggle, for transmission transfers.

CTR_TX

Bit 7: Correct Transfer for transmission.

EP_KIND

Bit 8: Endpoint kind.

EP_TYPE

Bits 9-10: Endpoint type.

Allowed values:
0: Bulk: Bulk endpoint
1: Control: Control endpoint
2: Iso: Iso endpoint
3: Interrupt: Interrupt endpoint

SETUP

Bit 11: Setup transaction completed.

STAT_RX

Bits 12-13: Status bits, for reception transfers.

Allowed values:
0: Disabled: all reception requests addressed to this endpoint are ignored
1: Stall: the endpoint is stalled and all reception requests result in a STALL handshake
2: Nak: the endpoint is naked and all reception requests result in a NAK handshake
3: Valid: this endpoint is enabled for reception

DTOG_RX

Bit 14: Data Toggle, for reception transfers.

CTR_RX

Bit 15: Correct transfer for reception.

CNTR

control register

Offset: 0x40, reset: 0x00000003, access: read-write

15/15 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTRM rw	PMAOVRM rw	ERRM rw	WKUPM rw	SUSPM rw	RESETM rw	SOFM rw	ESOFM rw	L1REQM rw		L1RESUME rw	RESUME rw	FSUSP rw	LPMODE rw	PDWN rw	FRES rw

Toggle Fields.

FRES

Bit 0: Force USB Reset.

Allowed values:
0: NoReset: Clear USB reset
1: Reset: Force a reset of the USB peripheral, exactly like a RESET signaling on the USB

PDWN

Bit 1: Power down.

Allowed values:
0: Disabled: No power down
1: Enabled: Enter power down mode

LPMODE

Bit 2: Low-power mode.

Allowed values:
0: Disabled: No low-power mode
1: Enabled: Enter low-power mode

FSUSP

Bit 3: Force suspend.

Allowed values:
0: NoEffect: No effect
1: Suspend: Enter suspend mode. Clocks and static power dissipation in the analog transceiver are left unaffected

RESUME

Bit 4: Resume request.

Allowed values:
1: Requested: Resume requested

L1RESUME

Bit 5: LPM L1 Resume request.

Allowed values:
1: Requested: LPM L1 request requested

L1REQM

Bit 7: LPM L1 state request interrupt mask.

Allowed values:
0: Disabled: L1REQ Interrupt disabled
1: Enabled: L1REQ Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

ESOFM

Bit 8: Expected start of frame interrupt mask.

Allowed values:
0: Disabled: ESOF Interrupt disabled
1: Enabled: ESOF Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

SOFM

Bit 9: Start of frame interrupt mask.

Allowed values:
0: Disabled: SOF Interrupt disabled
1: Enabled: SOF Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

RESETM

Bit 10: USB reset interrupt mask.

Allowed values:
0: Disabled: RESET Interrupt disabled
1: Enabled: RESET Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

SUSPM

Bit 11: Suspend mode interrupt mask.

Allowed values:
0: Disabled: Suspend Mode Request SUSP Interrupt disabled
1: Enabled: SUSP Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

WKUPM

Bit 12: Wakeup interrupt mask.

Allowed values:
0: Disabled: WKUP Interrupt disabled
1: Enabled: WKUP Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

ERRM

Bit 13: Error interrupt mask.

Allowed values:
0: Disabled: ERR Interrupt disabled
1: Enabled: ERR Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

PMAOVRM

Bit 14: Packet memory area over / underrun interrupt mask.

Allowed values:
0: Disabled: PMAOVR Interrupt disabled
1: Enabled: PMAOVR Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

CTRM

Bit 15: Correct transfer interrupt mask.

Allowed values:
0: Disabled: Correct Transfer (CTR) Interrupt disabled
1: Enabled: CTR Interrupt enabled, an interrupt request is generated when the corresponding bit in the USB_ISTR register is set

ISTR

interrupt status register

Offset: 0x44, reset: 0x00000000, access: Unspecified

11/11 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
CTR r	PMAOVR rw	ERR rw	WKUP rw	SUSP rw	RESET rw	SOF rw	ESOF rw	L1REQ rw			DIR r	EP_ID r

Toggle Fields.

EP_ID

Bits 0-3: Endpoint Identifier.

Allowed values: 0-15

DIR

Bit 4: Direction of transaction.

Allowed values:
0: To: data transmitted by the USB peripheral to the host PC
1: From: data received by the USB peripheral from the host PC

L1REQ

Bit 7: LPM L1 state request.

Allowed values:
1: Received: LPM command to enter the L1 state is successfully received and acknowledged

ESOF

Bit 8: Expected start frame.

Allowed values:
1: ExpectedStartOfFrame: an SOF packet is expected but not received

SOF

Bit 9: start of frame.

Allowed values:
1: StartOfFrame: beginning of a new USB frame and it is set when a SOF packet arrives through the USB bus

RESET

Bit 10: reset request.

Allowed values:
1: Reset: peripheral detects an active USB RESET signal at its inputs

SUSP

Bit 11: Suspend mode request.

Allowed values:
1: Suspend: no traffic has been received for 3 ms, indicating a suspend mode request from the USB bus

WKUP

Bit 12: Wakeup.

Allowed values:
1: Wakeup: activity is detected that wakes up the USB peripheral

ERR

Bit 13: Error.

Allowed values:
1: Error: One of No ANSwer, Cyclic Redundancy Check, Bit Stuffing or Framing format Violation error occurred

PMAOVR

Bit 14: Packet memory area over / underrun.

Allowed values:
1: Overrun: microcontroller has not been able to respond in time to an USB memory request

CTR

Bit 15: Correct transfer.

Allowed values:
1: Completed: endpoint has successfully completed a transaction

FNR

frame number register

Offset: 0x48, reset: 0x0000, access: read-only

5/5 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RXDP r	RXDM r	LCK r	LSOF r		FN r

Toggle Fields.

FN

Bits 0-10: Frame number.

Allowed values: 0-2047

LSOF

Bits 11-12: Lost SOF.

Allowed values: 0-3

LCK

Bit 13: Locked.

Allowed values:
1: Locked: the frame timer remains in this state until an USB reset or USB suspend event occurs

RXDM

Bit 14: Receive data - line status.

Allowed values:
1: Received: received data minus upstream port data line

RXDP

Bit 15: Receive data + line status.

Allowed values:
1: Received: received data plus upstream port data line

DADDR

device address

Offset: 0x4C, reset: 0x0000, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								EF rw	ADD rw

Toggle Fields.

ADD

Bits 0-6: Device address.

Allowed values: 0-127

EF

Bit 7: Enable function.

Allowed values:
0: Disabled: USB device disabled
1: Enabled: USB device enabled

BTABLE

Buffer table address

Offset: 0x50, reset: 0x0000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
BTABLE rw

Toggle Fields.

BTABLE

Bits 3-15: Buffer table.

Allowed values: 0-8191

LPMCSR

LPM control and status register

Offset: 0x54, reset: 0x0000, access: Unspecified

4/4 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								BESL r				REMWAKE r		LPMACK rw	LPMEN rw

Toggle Fields.

LPMEN

Bit 0: LPM support enable.

Allowed values:
0: Disabled: enable the LPM support within the USB device
1: Enabled: no LPM transactions are handled

LPMACK

Bit 1: LPM Token acknowledge enable.

Allowed values:
0: Nyet: the valid LPM Token will be NYET
1: Ack: the valid LPM Token will be ACK

REMWAKE

Bit 3: bRemoteWake value.

BESL

Bits 4-7: BESL value.

Allowed values: 0-15

BCDR

Battery charging detector

Offset: 0x58, reset: 0x0000, access: Unspecified

9/9 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
DPPU rw								PS2DET r	SDET r	PDET r	DCDET r	SDEN rw	PDEN rw	DCDEN rw	BCDEN rw

Toggle Fields.

BCDEN

Bit 0: Battery charging detector (BCD) enable.

Allowed values:
0: Disabled: disable the BCD support
1: Enabled: enable the BCD support within the USB device

DCDEN

Bit 1: Data contact detection (DCD) mode enable.

Allowed values:
0: Disabled: Data contact detection (DCD) mode disabled
1: Enabled: Data contact detection (DCD) mode enabled

PDEN

Bit 2: Primary detection (PD) mode enable.

Allowed values:
0: Disabled: Primary detection (PD) mode disabled
1: Enabled: Primary detection (PD) mode enabled

SDEN

Bit 3: Secondary detection (SD) mode enable.

Allowed values:
0: Disabled: Secondary detection (SD) mode disabled
1: Enabled: Secondary detection (SD) mode enabled

DCDET

Bit 4: Data contact detection (DCD) status.

Allowed values:
0: NotDetected: data lines contact not detected
1: Detected: data lines contact detected

PDET

Bit 5: Primary detection (PD) status.

Allowed values:
0: NoBCD: no BCD support detected
1: BCD: BCD support detected

SDET

Bit 6: Secondary detection (SD) status.

Allowed values:
0: CDP: CDP detected
1: DCP: DCP detected

PS2DET

Bit 7: DM pull-up detection status.

Allowed values:
0: Normal: Normal port detected
1: PS2: PS2 port or proprietary charger detected

DPPU

Bit 15: DP pull-up control.

Allowed values:
0: Disabled: signalize disconnect to the host when needed by the user software
1: Enabled: enable the embedded pull-up on the DP line

WWDG

0x40002C00: Window watchdog

6/6 fields covered. Toggle Registers.

CR

Control register

Offset: 0x0, reset: 0x0000007F, access: read-write

2/2 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
								WDGA rw	T rw

Toggle Fields.

T

Bits 0-6: 7-bit counter.

Allowed values: 0-127

WDGA

Bit 7: Activation bit.

Allowed values:
0: Disabled: Watchdog disabled
1: Enabled: Watchdog enabled

CFR

Configuration register

Offset: 0x4, reset: 0x0000007F, access: read-write

3/3 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
						EWI rw	WDGTB rw		W rw

Toggle Fields.

W

Bits 0-6: 7-bit window value.

Allowed values: 0-127

WDGTB

Bits 7-8: Timer base.

Allowed values:
0: Div1: Counter clock (PCLK1 div 4096) div 1
1: Div2: Counter clock (PCLK1 div 4096) div 2
2: Div4: Counter clock (PCLK1 div 4096) div 4
3: Div8: Counter clock (PCLK1 div 4096) div 8

EWI

Bit 9: Early wakeup interrupt.

Allowed values:
1: Enable: interrupt occurs whenever the counter reaches the value 0x40

SR

Status register

Offset: 0x8, reset: 0x00000000, access: read-write

1/1 fields covered.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16

15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
															EWIF rw

Toggle Fields.

EWIF

Bit 0: Early wakeup interrupt flag.

Allowed values:
1: Pending: The EWI Interrupt Service Routine has been triggered
0: Finished: The EWI Interrupt Service Routine has been serviced